YCS 0.02mm Silver Jumper Wire for Mobile PCB Repair

₨ 700

Fine Silver Jumper Wire for PCB Repair

The YCS 0.02mm Silver Jumper Wire gives you a 100m spool of hair-fine conductor for rebuilding broken traces and lifted pads on mobile phone motherboards. YCS describes the wire as non-magnetic, easy to tin, and low in solder resistance, so your joints stay clean under the microscope. It suits CPU and BGA pad repair, charging port and connector pad recovery, and any hardware fault where a trace needs a bridge. Mechanicpk stocks the YCS 0.02mm Silver Jumper Wire for technicians in Pakistan who need dependable fine-pitch rework consumables. Pair it with a hot air station, a soldering station, and a microscope for best results.

In stock

17 People watching this product now!
Description

YCS 0.02mm Silver Jumper Wire: Fine-Pitch Trace Repair Consumable

The YCS 0.02mm silver jumper wire is a hair-fine flying wire that bridges damaged traces and lifted pads where a thicker jumper would short against neighbouring joints. Mechanicpk supplies it as a 100m spool in a clear plastic case for repair shops and service centres across Pakistan that work at board level. A conductor this thin fits between pads on a CPU footprint, a connector, or a charging port, and you tack it down with a small amount of solder. The wire does one job well: it restores continuity on a mobile PCB without adding bulk or risking a bridge to the next pad.

How the Wire Behaves Under the Iron

YCS describes this wire as non-magnetic, tough, easy to tin, and free of breakpoints, with low solder resistance and low inductance. Each trait shows up at the bench. A non-magnetic conductor will not jump toward tweezers or a magnetised tip, so you place it exactly where you aim. Easy tinning means the wire accepts solder after a short touch of the iron, which limits heat on the surrounding pad and laminate. The manufacturer also lists high elongation and good plastic ductility, so you can bend the wire around a pad edge without snapping it. Low solder resistance and low inductance keep a repaired line close to the behaviour of the original trace, although no jumper matches the original copper exactly. The 0.02mm diameter reaches fine-pitch spots that heavier wire cannot.

Where It Fits in a Mobile Repair Workflow

A jumper wire step sits after diagnosis and before final testing. You confirm an open trace or missing pad with a multimeter in diode mode, clean the area, and expose the nearest sound copper or test point. Cut a short length, tin both ends, and solder one end to the surviving pad or via and the other to the target pad. A hot air station or a temperature-controlled soldering station handles the surrounding rework, and a microscope makes the 0.02mm size practical to place. Technicians use this approach on a charging issue from a torn charging port pad, a display problem from a broken connector trace, a network issue from a lifted pad on the RF section, or a dead phone where a lifted CPU or BGA pad leaves a ball without contact. When a chip needs to come off the board first, a reballing kit and a PCB holder complete the setup. After the bridge, you test the line again before you close the phone.

Gauge, Spool Size, and Companion Tools

A 100m spool covers a high volume of repairs because each jumper uses only a short cut length. At 0.02mm, this YCS 0.02mm silver jumper wire sits at the fine end of the range, so reserve it for pads and traces where space is tight. YCS also lists a 0.04mm copper version that gives you a sturdier bridge on wider pads, so you can match the gauge to each board. Handle the wire with fine tweezers, keep it in its case between jobs, and avoid kinks that weaken a short run. A workshop that sees dead phone and hardware fault boards daily will go through this consumable steadily. For the flashing side of the same repair, browse the ISP pinout tools, eMMC programmers, UFS adapters, and test boxes in the Mechanicpk range.

Additional information
Weight0.3 kg
Q & A
Please login to post questions

Key Features

  • 0.02mm ultra-fine diameter for tight pad spacing
  • 100m spool for high-volume repair work
  • Non-magnetic wire for controlled placement
  • Easy to tin with a short iron touch
  • Tough wire with no breakpoints
  • Low solder resistance and low inductance
  • High elongation and good plastic ductility
  • Clear plastic case for storage

Specifications

BrandYCS
Model0.02mm Silver Jumper Wire
CategoryJumper Wire (Soldering Consumables)
CompatibilityUniversal — not device-specific
Diameter0.02mm
Length100m
PackagingClear plastic case

Common Repair Uses

  • Trace and pad bridging on mobile phone motherboards
  • Rebuilding broken PCB traces
  • Replacing lifted or torn pads
  • CPU and BGA pad repair
  • Charging port pad recovery
  • Display connector trace repair
  • Fingerprint flex pad repair
  • Screw-hole trace repair on motherboards
  • Bridging test points after board cleaning

Compatible Devices

  • Universal jumper wire for mobile phone and tablet PCBs — not device-specific
  • Android smartphone motherboards
  • iPhone logic boards
  • Tablet motherboards
  • CPU and BGA pad footprints
  • Charging port connector pads
  • Display and flex connector pads
  • Fingerprint sensor flex pads
  • Battery connector pads

FAQ

What is the product name?
The product name is YCS 0.02mm Silver Jumper Wire.
What is the brand of this product?
The brand of this product is YCS.
What is the model of this product?
The model of this product is 0.02mm Silver Jumper Wire.
What is this product used for?
This product is used for bridging broken traces and replacing lifted pads on mobile phone and tablet motherboards.
Which devices are compatible with this product?
This product is universal and works on mobile phone and tablet PCBs. It is not tied to specific device models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Is the YCS 0.02mm jumper wire non-magnetic and easy to solder?
Yes. YCS lists the wire as non-magnetic, easy to tin, and low in solder resistance, with no breakpoints.
Which YCS jumper wire gauge should I use for wider pads?
YCS also lists a 0.04mm copper jumper wire. Use the 0.02mm silver wire for fine pads and tight spacing, and the 0.04mm copper wire for a sturdier bridge on wider pads.