YCS 7SS Soldering Flux Paste – Lead-Free 10cc
₨ 800
YCS 7SS Soldering Flux Paste, 10cc
The YCS 7SS soldering flux paste is a lead-free, halogen-free flux for tinning pads, BGA chip soldering, and fine-pitch work on mobile phone and PC circuit boards. Supplier data lists low smoke, solder insulation that helps avoid short circuits, and stable flow during heating. The 10cc toothpaste-style pack fits a repair bench and opens without a separate push rod. Mechanicpk supplies it to technicians and repair shops across Pakistan who handle IC change, reballing, and pad repair every day and want a spec-clear flux next to their hot air station and soldering station.
In stock
YCS 7SS Soldering Flux Paste for Precision Tinning and BGA Rework
The YCS 7SS soldering flux paste gives your repair bench a lead-free, halogen-free flux in a 10cc pack, built for tinning, BGA chip work, and fine-pitch soldering on phone logic boards. Mechanicpk stocks it for technicians who want a defined flux chemistry instead of an unlabeled jar of unknown composition. If your daily jobs include IC change karna on a dead phone, reballing after a hardware fault, or rebuilding a lifted pad, the flux decides whether the joint wets cleanly on the first pass or forces you to redo the work.
Lead-Free, Halogen-Free Chemistry on the Bench
Supplier listings describe the YCS 7SS as a lead-free and halogen-free soldering flux, a combination that suits lead-free alloys and the tight trace spacing on modern phone boards. Halogen-free formulation targets the aggressive residue that attacks fine copper over time. The same listings point to low smoke during heating, so you keep sight of the pad and the ball instead of working through a cloud over the chip. They also credit the flux with solder insulation that helps prevent short circuits between neighbouring pads, and with good flow stability, which means the paste holds its place and wets the joint without creeping away from the work area. These traits matter when you tin a pad, drag solder across a connector, or lay a thin film under a BGA package before you apply heat.
Where It Fits in a Board-Level Repair
Flux sits at the centre of every rework step. Before you lift a CPU, eMMC, or power IC with a hot air station, a thin flux layer spreads heat evenly across the package and protects the solder from oxidising. After the chip comes off, you clean the pads with a soldering station and braid, and fresh flux helps the new tin flow flat instead of balling up. During reballing, flux holds the balls in position until reflow. You also reach for it when you fix a charging port joint, rebuild a damaged pad, or tin jumper wires for ISP pinout work on a dead after flash phone. Build the full workflow around it with a temperature-controlled Soldering Station, a Hot Air Station, a Microscope for joint inspection, a Reballing Kit, and PCB Holders that keep the board steady while you work. A Multimeter confirms continuity once the joint cools.
Pack Format and Handling
The 10cc toothpaste-style pack uses a lid designed to open without an extra push rod, so you start working without hunting for a pin on a crowded bench. A small pack suits flux, because you use a little per joint and the material stays fresher than a large open pot that collects dust and moisture. Keep the cap on after every job and store the pack away from direct heat. For shops that run several technicians, a few packs spread across benches cost less than one shared jar that travels between stations and picks up contamination on the way.
Choosing the YCS 7SS for Your Workflow
Pick the YCS 7SS when your priority is controlled tinning and clean BGA soldering on mobile and PC boards at an everyday workshop price point. The flux does not replace solder paste or a stencil, and it does not depend on a specific phone brand or chipset family. It supports the soldering step itself, so it works across Samsung, Oppo, Vivo, Infinix, Tecno, and iPhone boards alike whenever the job calls for flux. Pair it with the right alloy and the right heat profile, and it gives you a consistent starting point for every joint you make.
| Weight | 0.3 kg |
|---|
Key Features
- ✓Lead-free formulation
- ✓Halogen-free formulation
- ✓Easy tinning on pads and wires
- ✓Low smoke during heating
- ✓Solder insulation that helps avoid short circuits
- ✓Good flow stability
- ✓10cc pack size
- ✓Toothpaste-style pack with lid that opens without a push rod
Specifications
| Brand | YCS |
|---|---|
| Model | 7SS (10cc) |
| Category | Soldering Flux |
| Compatibility | Universal soldering flux, not device-specific |
| Technology | Lead-free, halogen-free flux |
Common Repair Uses
- ✓Flux support for soldering and rework tasks on phone and PCB repair benches
- ✓BGA chip soldering
- ✓Pad tinning
- ✓IC removal and refit
- ✓Reballing support
- ✓Lifted or damaged pad rebuilding
- ✓Charging port joint repair
- ✓Jumper wire tinning for ISP work
Compatible Devices
- ✓Universal flux for mobile phone, PC, and computer circuit boards, not tied to a single brand or chipset family
- ✓Mobile phone logic boards (brand-independent)
- ✓Computer and PC circuit boards
- ✓BGA chip packages
- ✓Fine-pitch SMD pads
- ✓Board-level tinning and joint work
- ✓Flex and connector pad soldering
- ✓Jumper wire tinning points
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is YCS 7SS flux lead-free and halogen-free?
Can I use YCS 7SS flux for BGA tinning on mobile phone boards?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



