YCS 9G Wood Blade Handle for Phone CPU & NAND Glue Removal
₨ 800
YCS 9G Wood Blade Handle for CPU and NAND Work
The YCS 9G Wood Blade Handle is a 9 g, 140 x 8 mm holder for glue removal around phone CPU and NAND chips. Its ultra-light wooden body, textured grip, and matte finish give you steady blade control while you cut underfill, separate stuck chips, and clear adhesive from motherboards. Use it for mobile phone chip removal, motherboard CPU delamination, hard drive glue removal, circuit repair, and keyboard maintenance. Pair it with the YCS blade set, or order the handle alone to refit your bench. Mechanicpk supplies this YCS 9G wood blade handle to technicians and repair shops across Pakistan.
In stock
YCS 9G Wood Blade Handle for Board-Level Glue Removal
The YCS 9G wood blade handle gives you a light, controlled holder for the glue removal work that board-level repair demands. Every technician who lifts a CPU or NAND chip knows that a clean cut through the underfill decides whether the chip comes off intact or pulls pads with it. This handle weighs 9 g and measures 140 x 8 mm, so it sits in your fingers like a pen and lets you steer the edge with small, deliberate strokes. Mechanicpk supplies it to technicians who prefer measured scraping over aggressive prying.
Handle Build and Grip Control
The body uses an ultra-light wooden construction with a textured, matte finish. The texture keeps the handle from slipping when flux, alcohol, or residue coats your fingertips, and the matte surface avoids the slick feel of polished plastic. At 9 g, the tool puts almost no strain on your wrist, which matters when you clear glue from several boards in one sitting. The 140 mm length lets you choke up near the blade for fine work along a pad edge, then slide your grip back to sweep a longer line around the full outline of a CPU. You control pressure with your fingertips, not your whole hand, and that control protects the solder pads under the adhesive.
Where the Handle Fits in a Chip-Off Workflow
When a dead phone or a boot loop issue points to a damaged NAND or CPU, the repair starts the same way: you soften the glue, cut it, and lift the chip. You warm the area with a hot air station, then run the blade along the chip edge to break the adhesive bond. A CPU glue removal blade handle like this one carries the blade through that cut. The same handle serves mobile phone chip removal, motherboard CPU delamination, and hard drive glue removal.
After the chip lifts, you clean the pads with a soldering station, inspect them under a microscope, and reball the chip with a reballing kit before you refit it. A PCB holder keeps the board steady while you cut, and a multimeter confirms pad continuity afterward. The handle also works for general electronic circuit repair and keyboard maintenance, so it earns a place on your repair bench beyond phone work. For a charging issue or hardware fault that needs a chip change, you reach for it early in the job.
Choosing the Handle, the Blade Set, or Both
YCS sells this tool in three configurations: the 9G handle alone, the 9-piece blade set alone, or the handle with the blade set. The blades in the set carry a hand-polished edge for sharpness and durability. Choose the combination if you build a new bench kit, because it gives you the holder and nine blades in one order. Choose the handle alone if you already own YCS blades and want a spare holder for a second workstation. Pick the blade set alone to restock edges while you keep your current handle.
Wipe the blade after each job and swap any edge that starts to drag, because a dull edge forces extra pressure and puts pads at risk. Confirm the variation you select on the product page before you order. If you want a NAND glue removal tool that keeps your hand steady and your workflow clean, the YCS 9G wood blade handle fits that role.
| Weight | 0.9 kg |
|---|
Key Features
- ✓Compact 9 g body for low fatigue during long sessions
- ✓Ultra-light wooden handle
- ✓Non-slip textured grip
- ✓Matte finish for a steady hold
- ✓140 x 8 mm size for fine and sweeping blade control
- ✓Hand-polished blades for a sharp, durable edge (YCS blade set)
- ✓Suited to CPU and NAND glue removal, chip removal, and delamination
- ✓Available as handle only, 9-piece blade set only, or handle plus blade set
Specifications
| Brand | YCS |
|---|---|
| Model | Ultra-light 9G Knife Holder (YCS 9G) |
| Category | Mobile Repair Hand Tools |
| Compatibility | Universal glue removal tool, not device-specific |
| Material | Wooden handle, matte textured finish |
| Dimensions | 140 x 8 mm |
| Weight | 9 g |
Common Repair Uses
- ✓CPU glue removal on phone motherboards
- ✓NAND chip glue removal
- ✓Mobile phone chip removal
- ✓Motherboard CPU delamination
- ✓Hard drive glue removal
- ✓Electronic circuit repair
- ✓Keyboard maintenance
- ✓General mobile phone repair
Compatible Devices
- ✓Universal use, not tied to specific phone models or chipsets
- ✓Mobile phone motherboards (all brands, model-independent)
- ✓Phone CPU areas with glue or underfill
- ✓Phone NAND chip areas with glue or underfill
- ✓Electronic circuit boards
- ✓Computer keyboards
- ✓Hard drive boards
- ✓Other digital devices needing glue removal
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can the YCS 9G handle remove glue around a phone CPU or NAND chip?
What are the size and weight of the YCS 9G wood blade handle?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



