YCS No.2 Welding Oil 10cc for Mobile PCB & BGA Repair
₨ 600
YCS No.2 Welding Oil 10cc for Mobile PCB Repair
YCS No.2 welding oil 10cc is a flux for mobile motherboard and PCB soldering. It helps solder wet the pad during IC removal, reinstallation, BGA reballing, pad tinning and SMD work, so your joints form cleanly on the first pass. The 10cc bottle fits a daily repair bench, whether you handle dead phone cases, charging issues or hang on logo faults. Pair it with your Hot Air Station, Reballing Kit and Microscope for a complete rework setup. Mechanicpk supplies YCS No.2 welding oil 10cc to technicians, repair shops and service centers across Pakistan.
In stock
YCS No.2 Welding Oil 10cc for Board-Level Soldering
The YCS No.2 welding oil 10cc gives your bench a dedicated flux for the soldering jobs that decide whether a repair holds or fails. Every IC change karna job, every reballed CPU and every jumper wire you solder depends on solder that wets the pad and flows cleanly, and flux makes that happen. YCS builds this welding oil for mobile motherboard and PCB work, and the 10cc bottle suits technicians who go through flux daily on a busy repair bench.
When you heat a pad, a solder ball or a component lead, oxide forms on the metal and stops solder from bonding. Flux clears that barrier at soldering temperature and carries heat into the joint, so solder spreads across the pad instead of beading up. You apply a thin layer before reflow, bring your tool to temperature, and watch the solder pull into place. Flux is not an optional extra on a rework bench. It sits at the start of every soldering step.
Process Role of Welding Oil in Rework
Think of welding oil as the first layer in any hot air or soldering iron job. Before you lift an IC with your Hot Air Station, a small amount of flux around the package lets heat spread evenly and loosens the solder under it. When you reinstall the chip, fresh flux on the cleaned pads helps the solder wet properly the first time. On a Soldering Station, the same flux makes pad tinning and jumper lagana faster and cleaner, because the solder follows the iron tip instead of fighting it.
Pair it with Reballing Kits when you rebuild BGA packages. Bare pads and fresh balls need flux to form a joint that survives repeated heat cycles in a working phone. Technicians use flux of this type on CPU, NAND and PMIC work, and the same habit carries over to tablet and computer boards. After you rebuild an eMMC or UFS chip, you confirm the result with your eMMC Programmers, ISP Pinout Tools or UFS Adapters, so a clean joint saves you a second reballing round.
Where It Earns Its Place on the Repair Bench
Most hardware fault cases end with solder work on the board. A dead phone with a lifted pad needs pad repair and tinning. A charging issue traced to a charging IC needs a clean removal and reinstall. A display problem from a backlight or connector area needs careful micro-soldering. A hang on logo case that points to NAND needs reballing, and a network issue that sends you to the baseband area needs the same discipline. Each of these jobs goes smoother when flux is already on the pad.
Work under a Microscope, hold the board firm in a PCB Holder, and apply the oil in small amounts. Too much flux spreads onto neighbouring pads and makes the board harder to inspect. After the joint cools, check continuity with your Multimeter and test the repaired circuit with your Test Box before you close the phone. If you need a spotless board for customer delivery, wipe the area with isopropyl alcohol once the work is done.
Buying Notes for Pakistani Repair Shops
Shop owners and service centers burn through consumables faster than tools, so a 10cc bottle per technician keeps the workflow moving without constant reordering. YCS also sells a No.1 welding fluid in the same range, so read the No.1 and No.2 labels before you mix stock on a shared bench, and keep each bottle capped when you finish. Work in a ventilated space or under a fume extractor, and keep flux away from your eyes and skin.
Mechanicpk supplies this welding oil alongside the soldering, rework and testing equipment a repair workshop needs. You can build the full bench from one order: flux, Hot Air Stations, Soldering Stations, Reballing Kits, Microscopes and PCB Holders. Order YCS No.2 welding oil 10cc from Mechanicpk and keep your solder work consistent on every board that comes through your shop.
| Weight | 0.15 kg |
|---|
Key Features
- ✓10cc bottle size for daily workshop use
- ✓Welding oil (flux) made for mobile motherboard and PCB soldering
- ✓Supports IC removal and reinstallation with hot air or soldering iron
- ✓Helps solder wet the pad during BGA reballing
- ✓Suits pad tinning and jumper wire soldering
- ✓Fits CPU, NAND, PMIC and baseband-area rework
- ✓Works on tablet and computer boards as well as mobile phones
- ✓Sits in the YCS repair consumables range
Specifications
| Brand | YCS |
|---|---|
| Model | No.2 (10cc) |
| Category | Welding Oil / Soldering Flux |
| Compatibility | Universal — not device-specific |
Common Repair Uses
- ✓IC-level soldering, reballing and pad repair on mobile and PCB boards.
- ✓IC removal and reinstallation with hot air
- ✓BGA reballing on CPU and NAND chips
- ✓Pad tinning on bare or cleaned pads
- ✓SMD component soldering
- ✓Jumper wire soldering on damaged traces
- ✓Charging IC replacement
- ✓Dead phone board rework
- ✓Hang on logo NAND reflow and reballing
Compatible Devices
- ✓Universal — not device-specific. Works at board level on any phone, tablet or PCB where you solder or reball.
- ✓Android mobile phone motherboards
- ✓iPhone motherboards
- ✓Tablet PCBs
- ✓Computer and laptop boards
- ✓CPU BGA packages
- ✓NAND / eMMC chips
- ✓PMIC and charging ICs
- ✓Baseband-area components
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can I use YCS No.2 welding oil for BGA reballing on CPU and NAND chips?
Does YCS No.2 welding oil work on both Android and iPhone boards?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



