YCS NO.1 Welding Oil 15ML No-Clean Flux
₨ 700
No-Clean Flux Oil for Mobile Repair
YCS NO.1 Welding Oil 15ML is a halogen-free, lead-free, no-clean flux solder oil for mobile phone motherboard repair and precision microsoldering. The rosin-based formula improves solder wetting and heat transfer, protects pads from re-oxidation under heat, and leaves minimal non-conductive residue after reflow. You use it for BGA reballing, CPU, NAND, PMIC and baseband IC soldering, SMD component work and general PCB repair on phone, tablet and computer boards. The 15ML bottle gives a repair bench a steady supply for daily rework, and Mechanicpk delivers it to technicians, repair shops and service centers across Pakistan.
Out of stock
No-Clean Welding Oil for Mobile Repair: YCS NO.1 Welding Oil 15ML
YCS NO.1 Welding Oil 15ML gives your bench a dependable no-clean welding oil for mobile repair work, built around precision microsoldering on phone motherboards. YCS positions this flux solder oil for the steps where heat transfer and solder wetting decide whether a joint holds: CPU, NAND, PMIC and baseband IC soldering on boards that arrive as a dead phone or with a charging issue. The 15ML bottle suits workshops that reflow ICs every day, so you restock less often and keep one consistent flux across every technician’s station. Mechanicpk supplies it to repair shops, service centers and training institutes that want a low-residue flux without a separate cleaning step after every rework.
Flux Chemistry and Residue Behavior
The listing data for this YCS flux describes a halogen-free, lead-free, rosin-based formula, with high-performance synthetic rosin as the base. That composition targets two jobs on a mobile PCB. First, it strips oxides from pads and component leads, then lays down a protective film that stops re-oxidation while the board sits under heat. Second, it improves solder wetting, so molten solder spreads across the pad and forms a bright, solid joint instead of balling up. The flux also carries a high temperature drop point, which lets it tolerate hot air and iron temperatures without burning off early. After soldering, the residue stays minimal and non-conductive. That matters on dense boards, where leftover flux can create leakage paths between fine-pitch pads. You still wipe visible residue around connectors and shield cans when a clean finish matters for the customer, but you skip mandatory cleaning on every joint. Apply a thin, controlled film, and keep your iron or hot air temperature in the range your solder alloy needs.
Where YCS NO.1 Fits in a Board-Level Repair Workflow
Flux sits at the center of every soldering and rework step, so this oil touches most jobs on your bench. For BGA reballing, you coat the cleaned pads, place the stencil and solder balls, and reflow with a hot air station while the flux keeps the balls wetting evenly. For an IC change on a PMIC after a charging issue or another hardware fault, you apply the oil under and around the chip before you lift it, then again on the clean pads before you place the new part. NAND and CPU reflow follow the same pattern. For SMD work on capacitors, resistors and small connectors, a thin film on the pads gives clean fillets under a microscope. The listing data also confirms use on tablet and computer boards, so one bottle covers more than phones. Pair it with a soldering station, a hot air station, a reballing kit, PCB holders and a multimeter for continuity checks after each repair. When a dead-after-flash phone needs eMMC or UFS work, the same flux supports the reflow step before you move on to ISP pinout tools or an eMMC programmer.
Why Technicians Pick a 15ML No-Clean Flux
Buyers comparing flux options weigh residue, consistency and supply. A no-clean oil removes the most time-consuming step after soldering, and that saving adds up across a full day of boards. The 15ML volume lets you give each technician a personal bottle, so nobody shares one container and contaminates it with dirty tips or brushes. Keep the cap tight, store the bottle away from heat and wipe the applicator between boards, so the flux behaves the same on the last repair of the day as on the first. If your work moves toward finer BGA jobs, add a dedicated lead-free solder paste or reballing flux paste to the bench and keep this oil for routine soldering, desoldering and pad prep. That split keeps your consumable costs predictable and your workflow fast.
| Weight | 0.10 kg |
|---|
Key Features
- ✓No-clean formula with minimal, non-conductive residue
- ✓Halogen-free and lead-free composition
- ✓High-performance synthetic rosin base
- ✓Strong solder wetting for bright, solid joints
- ✓Improved heat transfer during reflow
- ✓Oxide removal with protection against re-oxidation under heat
- ✓High temperature drop point
- ✓15ML bottle for daily workshop use
Specifications
| Brand | YCS |
|---|---|
| Model | No.1 (Number One) |
| Category | Soldering Flux / Welding Oil |
| Compatibility | Universal — mobile phone, tablet and computer board soldering; not device-specific |
| Supported Devices | Mobile phone, tablet and computer boards |
| Technology | No-clean, halogen-free, lead-free, rosin-based flux |
| Material | High-performance synthetic rosin base |
| Volume | 15ML |
Common Repair Uses
- ✓BGA reballing and rework
- ✓CPU and NAND reflow
- ✓PMIC replacement after a charging issue
- ✓Baseband IC soldering
- ✓SMD component soldering
- ✓Desoldering and IC removal
- ✓Pad prep before placing a new chip
- ✓General PCB repair and maintenance
Compatible Devices
- ✓Universal flux for board-level soldering — not tied to specific phone models
- ✓Mobile phone motherboards (all brands)
- ✓Tablet logic boards
- ✓Computer and laptop boards
- ✓CPU chips and BGA processors
- ✓NAND / eMMC memory chips
- ✓PMIC and power management ICs
- ✓Baseband and other IC chips
- ✓SMD components on general PCBs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is YCS NO.1 welding oil halogen-free and lead-free?
Do I need to clean the board after using YCS NO.1 welding oil?
Related products
RELIFE RL-004SA silicone pad – Anti-slip
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



