Mechanic Sherlock V2.0 Digital Multimeter
₨ 14,500
Precision Voltage and PN Junction Tester
The Mechanic Sherlock V2.0 digital multimeter gives your repair bench a 25000-count, 4.5-digit reading with 0.2mV precision and a ±24.000V display range. You measure phone motherboard rails and PN junction drop on one compact unit (94 x 54 x 43 mm) that runs on a 900mAh battery or a 5V external supply. Use it to trace a dead phone to the shorted rail, verify charging lines, and confirm a rail after IC change karna. Mechanicpk supplies the Mechanic Sherlock V2.0 in Pakistan for technicians, repair shops, and service centers that need board-level voltage answers, not rough estimates.
In stock
Mechanic Sherlock V2.0 Multimeter for Board-Level Fault Tracing
The Mechanic Sherlock V2.0 multimeter does one job well: it gives you a trustworthy voltage reading on a phone logic board when a standard handheld meter rounds the answer away. It resolves 25000 counts (4.5 digits) and reads with 0.2mV precision, so a rail sitting a few millivolts low shows on the display instead of hiding behind a coarse reading. Mechanicpk stocks this tester for Pakistani technicians who handle dead phone, charging issue, and boot loop faults every day and need numbers they can compare against a schematic or a known-good board.
Measurement Specifications That Matter on the Bench
A 2000-count pocket meter shows you roughly one-twelfth of the detail this unit shows. That gap decides whether you catch a drooping rail or miss it. The voltage display range runs from -24.000V to +24.000V, which covers battery, charging, display bias, and PMIC output rails on a phone board with room to spare. Phone boards run on low-voltage rails, where millivolt accuracy matters more than a high-voltage ceiling. Voltage measurement error sits at 0.1%, a tolerance you can rely on when you compare a suspect board against a working donor. The PN junction range spans 0.0000 to 1.9999, so you read the forward drop of a diode or protection junction directly instead of guessing from a beep. The body measures 94 x 54 x 43 mm and fits beside a microscope without crowding your repair bench. A 900mAh battery runs the unit, and you can feed it from a 5V external supply during long diagnostic sessions.
Where It Fits in a Board-Level Repair Workflow
Start every hardware fault on the multimeter, not on the hot air station. On a dead phone, you check the battery connector voltage first, follow the main power rail through the PMIC, and compare each rail against a known-good board. The PN junction function speeds up short tracing: you probe a suspect line, read the junction value, and see which component drags the rail down before you commit to a rework. Display problem and network issue faults follow the same pattern, because both depend on clean supply rails reaching the display connector or the RF section. After IC change karna or jumper lagana, you measure again and confirm the rail now sits where the schematic says it should. The ON-OFF check supports quick continuity decisions on traces and jumpers, so you confirm a repair path before you close the phone. Record the reading before you touch anything: a voltage you log on the unrepaired board gives you a baseline, and a matching reading after the repair tells you the fault is gone rather than masked. Some boot loop and hang on logo cases come from a sagging rail, and a 0.2mV-level reading exposes that droop. Shops that run several benches give each technician their own unit, so nobody waits for the reference meter.
Pairing It With the Rest of Your Bench
A multimeter finds the fault; other tools fix it. Pair the Sherlock V2.0 with a hot air station and a soldering station from the Mechanicpk catalog for the rework itself, a microscope to inspect the suspect area, and a PCB holder to keep the board steady while you probe. If the fault hunt leads to storage, move on to ISP pinout tools, eMMC programmers, and UFS adapters. If it leads to BGA work, a reballing kit finishes the job. Test boxes handle the software side once the hardware passes. Technicians who start with a basic pocket meter often upgrade to this 4.5-digit unit once they need precision they can trust on every rail. Whether you run a one-man bench in Lahore or a service center in Karachi, the workflow stays the same: measure, isolate, rework, measure again.
| Weight | 0.150 kg |
|---|
Key Features
- ✓25000-count, 4.5-digit resolution
- ✓0.2mV measurement precision
- ✓-24.000V to +24.000V voltage display range
- ✓PN junction measuring range of 0.0000–1.9999
- ✓0.1% voltage measurement error
- ✓ON-OFF check for quick continuity decisions
- ✓900mAh battery with 5V external power supply input
- ✓Compact 94 x 54 x 43 mm body with HD digital display
Specifications
| Brand | Mechanic |
|---|---|
| Model | Sherlock V2.0 |
| Category | Multimeter / Voltage and PN Junction Tester |
| Compatibility | Universal — not device-specific |
| Technology | Digital voltage and PN junction measurement |
| Input Voltage | 5V (external power supply) |
| Dimensions | 94 x 54 x 43 mm |
| Resolution | 25000 counts (4.5 digits) |
| Precision | 0.2mV |
| Voltage Display Range | -24.000V to +24.000V |
| PN Junction Measuring Range | 0.0000–1.9999 |
| Voltage Measurement Error | 0.1% |
| Battery Capacity | 900mAh |
Common Repair Uses
- ✓Voltage and PN junction diagnosis at board level
- ✓Tracing a short on a dead phone
- ✓Checking charging issue rails and connector voltage
- ✓Verifying display problem power lines
- ✓Checking network issue supply rails
- ✓Reading PN junction drop on suspect components
- ✓Confirming rail voltage after IC change karna
- ✓Validating continuity after jumper lagana
- ✓Comparing a faulty board against a known-good donor board
Compatible Devices
- ✓Universal — works on phone logic boards and electronic circuit boards in general; not tied to specific models or chipsets
- ✓Android smartphone logic boards (all brands)
- ✓iPhone logic boards
- ✓Tablet motherboards
- ✓Battery connector and charging line test points
- ✓Display and backlight power rails
- ✓PMIC output rails
- ✓Diode and protection junction test points
- ✓General low-voltage electronic PCBs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What voltage range and precision does the Mechanic Sherlock V2.0 offer?
Can the Mechanic Sherlock V2.0 measure PN junction values on a phone motherboard?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



