Mechanic V90E Digital Multimeter – Voice Broadcast Meter
₨ 4,800
Voice Broadcast Multimeter for Repair Benches
The Mechanic V90E Digital Multimeter reads out your measurements by voice, so you keep both hands and both eyes on the board while you probe. It covers DC voltage from 200 mV to 1000 V, DC current up to 10 A, AC voltage and current, resistance from 200 Ω to 2 MΩ, and capacitance from 10 nF to 20 mF. The LED display stays readable in dark environments, and a groove on the body stores the test leads. Technicians diagnosing a dead phone, a charging issue, or a short on the battery line get fast, clear readings from a pocket-sized meter.
In stock
Mechanic V90E Digital Multimeter: Voice-Guided Measurement for Mobile Repair
The Mechanic V90E digital multimeter gives repair technicians a voice-guided meter that reads results aloud while you hold the probes on a live board. It is a pocket-sized multimeter for mobile repair, and its range list shows why. You get millivolt-level DC voltage steps, microamp current steps, resistance up to 2 MΩ, and a wide capacitance span. Whether you chase a dead phone, a charging issue, or a hardware fault that appears after a failed flash, you need a meter that answers quickly without pulling your eyes off the PCB. This listing breaks down what the V90E measures, where it fits on your bench, and what to know before you order from Mechanicpk.
Measurement Ranges That Match Board-Level Work
DC voltage runs across five steps: 200 mV, 2 V, 20 V, 200 V and 1000 V. The low steps suit the small voltages you check on a phone board, such as battery connector voltage, charging line voltage, and the rails that feed the display or network section. DC current offers 20 µA, 2 mA, 20 mA, 200 mA and 10 A, so you can check a low standby draw at one end and a charger’s real output at the other. AC voltage covers 2 V, 20 V and 200 V, and AC current covers 20 mA, 200 mA and 10 A. Resistance spans 200 Ω to 2 MΩ, which covers short-circuit hunting on power lines and checking cables and connectors by their resistance. Capacitance runs from 10 nF to 20 mF, so you can test suspect capacitors you remove from a board. The V90E does not measure inductance, so keep a separate tool for coil testing.
Voice Broadcast Multimeter Features at the Bench
Voice broadcast speaks each reading. That helps when you hold a probe on a tiny test point with one hand and steady the board with the other. You catch a changing value without a glance at the screen, which lowers the risk of a slipped probe bridging two pads. The LED display stays readable in dark environments and avoids glare, so it works under a microscope light or in a dim corner of a workshop. Clearly marked jacks show the maximum input for each socket, so you pick the right input before you measure current. A groove on the housing stores the test leads, and the leads carry fine tips that reach small points on a mainboard. The meter runs on a 9V battery. The battery does not come with the meter, so add one to your order.
Where It Fits in Your Repair Workflow
Start every board-level repair with measurements, and the V90E handles that first pass. On a dead phone, check battery voltage and current draw before you suspect the CPU or the eMMC. A charging issue calls for voltage readings at the charging port and along the charging IC lines, then a resistance check on suspect lines with the battery disconnected. A boot loop issue or a hang on logo often points to a weak power rail, and rail readings tell you whether the PMIC deserves a closer look before you reach for the hot air station. For a display problem or network issue, compare supply line voltages against a known-good board. After an IC change, read the neighbouring rails again before you power the phone. Pair the meter with a test box or ISP pinout tool when software and hardware faults overlap, with a PCB holder and microscope to steady your probing, and with your soldering station or reballing kit once readings confirm the faulty part. When every reading looks normal and the phone stays dead after flash, move on to eMMC programmers or UFS adapters.
Protection and Buying Notes for Your Workshop
The V90E carries double fuse protection and a 5 mm protective sleeve, which adds a layer of safety when you test current on the 10 A range. Move the lead to the correct jack and select the correct range before you touch the circuit. The meter weighs 358 g and fits a pocket or a tool roll. Mechanicpk stocks multimeters alongside microscopes, soldering stations, hot air stations and PCB holders, so you can equip a complete bench in one order. Repair shop owners who set up a new technician’s bench get voltage, current, resistance and capacitance checks in one handheld unit with spoken readings.
| Weight | 0.150 kg |
|---|
Key Features
- ✓Voice broadcast reads each measurement aloud
- ✓LED display readable in dark environments with no glare
- ✓Five-step DC voltage range from 200 mV to 1000 V
- ✓DC current from 20 µA up to 10 A
- ✓Resistance range from 200 Ω to 2 MΩ
- ✓Capacitance range from 10 nF to 20 mF
- ✓Double fuse protection with a 5 mm protective sleeve
- ✓Marked input jacks and a groove for storing the test leads
Specifications
| Brand | Mechanic |
|---|---|
| Model | V90E |
| Category | Digital Multimeter |
| Compatibility | Universal measurement tool, not device-specific |
| Technology | Digital multimeter with voice broadcast and LED display |
| DC Voltage Ranges | 200 mV, 2 V, 20 V, 200 V, 1000 V |
| DC Current Ranges | 20 µA, 2 mA, 20 mA, 200 mA, 10 A |
| AC Voltage Ranges | 2 V, 20 V, 200 V |
| AC Current Ranges | 20 mA, 200 mA, 10 A |
| Resistance Range | 200 Ω to 2 MΩ |
| Capacitance Range | 10 nF to 20 mF |
| Input Voltage | 9V battery (battery not included) |
| Weight | 358 g |
Common Repair Uses
- ✓Dead phone diagnosis by checking battery voltage and current draw
- ✓Charging issue tracing at the port and charging IC lines
- ✓Short-circuit hunting on power lines by resistance reading
- ✓Boot loop and hang-on-logo checks on power rails
- ✓Verification of rail voltages after an IC change
- ✓Display problem and network issue supply line checks
- ✓Testing suspect capacitors removed from a board
- ✓Charger and cable output checks on the 10 A range
Compatible Devices
- ✓Universal measurement scope. The meter tests any phone board and does not depend on a device model.
- ✓Android smartphone mainboards from Samsung, Oppo, Vivo, Infinix and Tecno
- ✓iPhone logic boards and battery connectors
- ✓Phone battery packs and battery connector lines
- ✓Charging port and charging IC lines on any phone
- ✓Power rail test points around the PMIC
- ✓Display and backlight supply lines
- ✓Mobile chargers and USB cables
- ✓Tablets and other small electronics boards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What voltage, current and resistance ranges does the Mechanic V90E support?
Can the Mechanic V90E measure capacitance and inductance, and which battery does it use?
Related products
RELIFE RL-004SA silicone pad – Anti-slip
In stock



