2UUL BH05 Screen Stand – LCD Side Hanging Fixture
₨ 5,500
2UUL BH05 LCD Screen Stand
The 2UUL BH05 screen stand holds a phone LCD in a side-hanging position while you work on the device. A suction cup fixes the display, so the screen stays clear of the board and the frame during disassembly. The BH05 uses a fixed, non-rotating design, which suits technicians who want a simple, stable fixture on the bench. You can use it for LCD replacement, charging port replacement, and general phone opening jobs. Mechanicpk supplies the 2UUL BH05 to repair shops and service centers across Pakistan as a dependable display-handling fixture.
In stock
2UUL BH05 Screen Stand for Side-Hanging LCD Repair Work
The 2UUL BH05 screen stand solves a basic bench problem: where the display goes once you open a phone. A loose LCD on the table risks scratches, flex tears, and cable strain, and it takes up room you need for the board. The BH05 grips the screen with a suction cup and hangs it at the side of the device, so the display stays supported while you work on the internals. 2UUL builds the BH05 as a fixed fixture without a rotating mechanism, which keeps the structure simple and the setup fast.
Fixed-Position Design and Suction Cup Mounting
The BH05 relies on a suction cup to fix the LCD in a side-hanging position. You press the display onto the cup, then hang the assembly beside the phone body. The fixture does not rotate, so the screen holds one orientation for the whole job. That suits straightforward repairs where you open the phone, reach the target component, and close it again without repositioning the display.
A fixed fixture also reduces moving parts. You adjust nothing mid-repair, and the display does not shift while you handle the frame, the battery connector, or the charging port flex. Technicians who prefer predictable, minimal tooling on a busy bench will find the BH05 easy to place and easy to clear away.
Where the BH05 Fits in the Repair Workflow
In a typical LCD replacement or charging port job, the display comes off early and sits in your way for the rest of the repair. The BH05 takes that display out of the work area. After you separate the screen with your usual heat and prying process, you mount it on the stand and continue with the board-level or module-level work underneath.
Charging issue repairs benefit the most. When you replace a charging port or sub-board, you need free access to the lower section of the frame, and a hanging screen keeps that area open. Display problem jobs follow the same pattern. You remove the damaged panel, fit the replacement, and use the stand to hold the new LCD safely while you test connections before final assembly.
The BH05 also pairs with the rest of a proper repair bench. Place it beside your hot air station for display separation, under a microscope setup for fine flex connector work, and next to a PCB holder when the job moves to the mainboard. Use a multimeter after reassembly to confirm charging current and battery voltage. Shops that handle high volumes of screen jobs often keep several fixtures at hand, so each phone keeps its display protected while the next job starts.
BH05 vs BH06: Choosing the Right 2UUL Fixture
2UUL sells a rotatable sibling, the BH06, alongside the BH05. The two share the side-hanging concept and the suction cup approach, and the difference comes down to movement. The BH06 rotates the screen, and the BH05 stays fixed. If your work needs the display turned to different angles, the BH06 gives you that option. If you mainly need a stable hanging point and want the simpler fixture, the BH05 covers the job without extra mechanism.
Why Repair Shops Stock the 2UUL BH05
The BH05 fits repair benches that process phones of many brands, because the fixture addresses a universal handling problem rather than a model-specific one. You get a consistent way to park the screen on every job, which cuts the risk of cracked panels and torn flex cables during repair. Each unit ships as a single 2UUL BH05 screen stand, so you can add fixtures to your bench one at a time as your workload grows. Confirm that your target display fits the suction cup surface before you buy in bulk, since screen sizes and glass shapes vary across handsets.
| Weight | 0.3 kg |
|---|
Key Features
- ✓Suction cup grip that fixes the LCD in place
- ✓Side-hanging layout that frees the work area around the phone
- ✓Fixed, non-rotatable design for a stable, simple setup
- ✓Universal approach to phone screen handling
- ✓Supports LCD replacement and charging port workflows
- ✓Single-unit pack: 1 x 2UUL BH05 screen stand
- ✓Fits alongside hot air station, microscope, and PCB holder setups
- ✓Brand-backed 2UUL fixture line with a rotatable BH06 option
Specifications
| Model | BH05 |
|---|---|
| Category | Screen Fixture / Phone Disassembly Stand |
| Compatibility | Universal mobile phone screens (not device-specific) |
| Technology | Suction cup side-hanging fixture, non-rotatable |
Common Repair Uses
- ✓Holding the display during phone opening and component-level access
- ✓Phone disassembly and screen parking
- ✓LCD replacement
- ✓Charging port replacement
- ✓Display problem repair
- ✓Keeping the screen clear of the board and frame during internal work
- ✓Holding a replacement LCD while you test connections
Compatible Devices
- ✓Universal fit for mobile phone LCD screens — not tied to specific models or chipsets
- ✓Universal mobile phone LCD screens
- ✓Phones of multiple brands handled in general repair shops
- ✓Displays removed during disassembly and charging port jobs
- ✓Replacement LCDs held during pre-assembly testing
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is the 2UUL BH05 screen stand rotatable?
What is the difference between 2UUL BH05 and BH06?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



