2UUL CS02 Cushion Seal Tape for Screen Frame & Back Cover
₨ 1,150
2UUL CS02 5mm Cushion Seal Tape
The 2UUL CS02 Cushion Seal Tape for Screen Frame & Back Cover gives your repair bench a 5mm double-sided cushion tape for rebuilding the bond between an LCD frame and a back cover. Each box holds five black rolls, so you cut the exact length each job needs instead of hunting for a pre-cut gasket. The flexible cushioning layer sits between the screen and the frame and absorbs pressure when you close the device. Use this 2UUL CS02 cushion seal tape on smartphones and tablets after screen replacement, back cover changes, or mid-frame repairs. Mechanicpk stocks it for technicians who want one consistent 5mm width for daily service work.
In stock
2UUL CS02 Cushion Seal Tape: 5mm Width for Frame and Cover Work
A clean repair can still fail at the last step. You replace the display, test the touch, close the phone over old or missing adhesive, and the screen lifts, rattles, or presses unevenly against the frame. The 2UUL CS02 Cushion Seal Tape for Screen Frame & Back Cover targets that final step. It is a 5mm double-sided cushion tape from 2UUL, sold as a box of five rolls, made for the joint between the LCD frame and the back cover on smartphones and tablets. This page covers what the CS02 does, where it fits in a repair, and how it differs from the 3mm CS01.
Cushion Layer and Adhesive Construction
The CS02 uses an ultra-flexible cushioning material with adhesive on both sides. That construction does two jobs at once. The adhesive holds the screen or back cover to the frame, and the cushion layer spreads clamping pressure so the LCD does not take the full load when you press the device shut. 2UUL positions the tape as a way to reduce compression damage to the display after installation. The black finish matches the dark inner edges of most frames, so a strip near a gap blends in.
The tape ships as a roll, not as a model-specific die-cut, so you control the length and the corners. You trim it with a blade or fine scissors and press it along the frame channel. Compatibility covers LCD frames, mid-frames, and back covers on smartphones and tablets. That scope is general, not model-specific, so check the border width of the device on your bench before you commit to the 5mm strip.
5mm CS02 Versus 3mm CS01: Choosing the Right Width
2UUL sells this tape in two widths. The CS01 runs 3mm and the CS02 runs 5mm, both in five-roll boxes. Pick the CS02 when the frame lip or back cover channel gives you room for a wider bond line, and pick the CS01 when the border is thin. Measure the channel with calipers before you cut, because a strip wider than the lip squeezes out under pressure and shows at the edge. Keep both widths in your drawer if your shop handles mixed brands and tablets, since border width changes from one model to the next.
The CS02 does not replace model-specific pre-cut adhesive. When an iPhone job requires restoring the original airtight seal, 2UUL lists dedicated pre-cut screen and back cover sealing adhesives in separate series.
Where the CS02 Fits in Your Repair Workflow
Tape work closes the job, so it follows every step before it. You separate the screen with a hot air station or heating plate, strip the old adhesive, clean the frame channel, inspect the board under a microscope, and confirm charging and display function before you seal. Then you lay the CS02 along the clean frame, press the screen or back cover into place, and hold it in a PCB holder or press while the bond sets. Wipe the frame with alcohol first, because dust and oil weaken any double-sided tape.
Handle the tape with clean gloves or tweezers so skin oil stays off the adhesive face. Lay the strip without stretching it, because stretched tape pulls back and leaves a gap at the corners. After the bond sets, retest touch response at the edges and check the panel for pressure marks. Technicians who fix display problem and loose back cover complaints use this routine daily, and shops with volume work buy the five-roll box so every bench keeps its own roll. Mechanicpk carries this tape alongside hot air stations, soldering stations, microscopes, multimeters, and PCB holders, so you cover the full repair routine from one supplier.
| Weight | 0.98 kg |
|---|
Key Features
- ✓5mm CS02 width for wider frame and cover channels
- ✓Double-sided adhesive for screen and back cover bonding
- ✓Ultra-flexible cushioning material that reduces compression on the LCD
- ✓Five rolls per box for multi-bench shops
- ✓Black finish that blends with dark frame edges
- ✓Cut-to-length roll format with no model-specific die-cut
- ✓Suits LCD frames, mid-frames, and back covers
- ✓Works on smartphones and tablets
Specifications
| Brand | 2UUL |
|---|---|
| Model | CS02 |
| Category | Repair Tools / Adhesive Tape |
| Compatibility | LCD frame / back cover, smartphone and tablet |
| Supported Devices | Smartphones and tablets |
| Material | Flexible cushioning material with double-sided adhesive |
| Dimensions | 5mm width |
| Weight | 98g gross weight (box of 5 rolls) |
Common Repair Uses
- ✓Real workflows where cushion tape closes the job.
- ✓Re-sealing an LCD frame after screen replacement
- ✓Refitting a back cover after a battery or board repair
- ✓Re-bonding a loose or lifted back cover
- ✓Replacing dried or damaged frame adhesive
- ✓Adding a cushion layer between the LCD and the frame to reduce pressure
- ✓Closing tablet screens after display work
- ✓Securing mid-frame joints after separation
- ✓Stocking one roll per bench for daily service jobs
Compatible Devices
- ✓Universal, not device-specific. The tape suits smartphone and tablet frames wide enough for a 5mm bond line.
- ✓Smartphone LCD screen frames
- ✓Smartphone back covers
- ✓Smartphone mid-frames
- ✓Tablet LCD screen frames
- ✓Tablet back covers
- ✓Any frame or cover channel that accepts a 5mm tape width
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What is the difference between 2UUL CS01 and CS02 cushion seal tape?
Can the 2UUL CS02 restore the waterproof seal on an iPhone?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



