338S00839 USB Charging IC for iPhone 14 Series

₨ 650

338S00839 USB Charging IC for iPhone 14 Repair

The 338S00839 USB charging IC replaces the Apple charging chip on iPhone 14, 14 Plus, 14 Pro, and 14 Pro Max logic boards. You use it when a phone shows no charging, slow charging, or ignores the cable after you rule out the connector, flex, and battery. The IC suits board-level repair with a hot air station, preheater, and microscope. Match the 338S00839 marking on the failed chip before you order, because iPhone 13 and iPhone 15 boards use different charging ICs. Mechanicpk supplies the part to technicians and repair shops across Pakistan.

10 People watching this product now!
Description

338S00839 USB Charging IC for iPhone 14 Series Repair

The 338S00839 USB charging IC is the Apple-marked power management chip in the charging path of the iPhone 14 family. It handles the exchange between the Lightning port, the connected charger, and the battery circuit, so a failure here shows up as no charging, slow charging, or a phone that ignores the cable entirely. If you run a repair bench in Pakistan and see iPhone 14 boards with a dead charging section, this IC is one of the first parts you check with your multimeter and DC power supply. Mechanicpk lists the part for technicians who replace it at board level.

Where the 338S00839 Sits in the iPhone 14 Charging Path

Apple places a dedicated USB charging IC between the Lightning connector and the main power rail so the board can negotiate with the charger before it accepts current. The 338S00839 fills that role on the iPhone 14, 14 Plus, 14 Pro, and 14 Pro Max. It works alongside the main PMIC, the battery management circuit, and the connector lines, so a fault in any of those neighbours can mimic a bad charging IC. You separate the cases by measuring VBUS at the connector, watching the supply current on a DC power supply, and checking for liquid damage around the charging section. Apple marks the chip with its 338S part prefix, and suppliers list the common revision as 338S00839-B0, so match the full marking on your failed chip before you order.

Fault Symptoms That Point to This IC

A damaged 338S00839 rarely behaves the same way on every board. You can see no charging at all, charging that stops after a few seconds, slow charging on a known good cable, or a phone that stays dead until you connect a DC power supply with the right current limit. Heat near the charging section on a DC supply points to a short, and a short often follows a fake charger, a bent connector, or liquid. Pakistani repair shops see “charging issue” and “dead phone” complaints after cheap adapters all the time, so you meet these faults regularly. Test the connector, the flex, and the battery first. Replace the IC only after your readings point to it, because a premature swap puts the pads and the board at risk. Record the supply current at each stage so you can compare the board before and after the swap.

Replacement Workflow and Bench Preparation

Plan the rework before you touch the board. Remove the shields, protect nearby components with Kapton tape, and preheat the board from below so the heat spreads evenly. Apply flux, lift the old IC with your hot air station at a temperature that suits the solder alloy on the board, and clean the pads with a soldering iron and wick under a microscope. Check every pad for lifted copper before you place the new chip. Tin or reball the IC as your process requires, align it under the microscope, and reflow it gently without pressing down. After the board cools, measure the lines again with your multimeter, then test on a DC power supply before you reassemble the phone. Let the phone charge for several minutes, watch for heat, and confirm the battery percentage rises. Select the correct IC marking before ordering, because iPhone 13 and iPhone 15 boards use different charging ICs and the wrong chip will not fit the circuit. A hot air station, flux, a PCB holder, and a microscope make this job repeatable, and a reballing kit helps if you prepare the chip yourself.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Apple 338S00839 marking for iPhone 14 series charging repair
  • Common -B0 revision marking for easy matching
  • Handles USB charging control on the board
  • Fits board-level replacement with hot air and preheat
  • Matches iPhone 14, 14 Plus, 14 Pro, and 14 Pro Max
  • Suits technicians who diagnose with a DC power supply
  • Works with standard microscope and flux rework
  • Supports repeatable results across repair shop volume

Specifications

BrandApple (part marking)
Model338S00839 (common revision marking: 338S00839-B0)
CategoryUSB Charging IC / Power Management IC
CompatibilityiPhone 14 series
Supported DevicesiPhone 14, iPhone 14 Plus, iPhone 14 Pro, iPhone 14 Pro Max

Common Repair Uses

  • Board-level charging repair on iPhone 14 series logic boards.
  • No charging after connector, flex, and battery checks pass
  • Slow charging on a known good cable and adapter
  • Charging that starts, then stops after a few seconds
  • Phone that ignores the cable and shows no charging response
  • Dead phone that draws abnormal current on a DC power supply
  • Heat near the charging section caused by a short
  • Damage after a fake or faulty charger
  • Charging section repair after liquid damage

Compatible Devices

  • Verified scope is the iPhone 14 series, based on distributor listings for the 338S00839-B0 marking.
  • iPhone 14
  • iPhone 14 Plus
  • iPhone 14 Pro
  • iPhone 14 Pro Max

FAQ

What is the product name?
The product name is 338S00839 USB Charging IC.
What is the brand of this product?
The brand of this product is Apple (part marking).
What is the model of this product?
The model of this product is 338S00839, with the common 338S00839-B0 revision marking.
What is this product used for?
This product is used for replacing the USB charging IC on iPhone 14 series logic boards to fix charging faults.
Which devices are compatible with this product?
This product is compatible with iPhone 14, iPhone 14 Plus, iPhone 14 Pro, and iPhone 14 Pro Max.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can I use the 338S00839 on an iPhone 13 or iPhone 15 board?
No. iPhone 13 boards use the 338S00770 and iPhone 15 boards use the 338S00946, so check the marking on the original chip before you order.
How do I check if the 338S00839 causes a charging issue on an iPhone 14?
Connect a DC power supply, read the current draw, measure VBUS at the connector, and check for heat or a short near the charging section. Rule out the connector, flex, and battery first, then replace the IC if your readings point to it.