MT6360UP Power IC – MediaTek Charger PMIC

₨ 350

MT6360UP Power IC for MediaTek Board Repair

The MT6360UP is a MediaTek multifunction PMIC that combines a battery charger, OTG boost, Type-C and Power Delivery control, buck converters, LDO regulators, and LED drivers in one chip. You replace it on boards where the charging path or secondary power rails fail and the phone shows no charge, a dead state, or no USB detection. Mechanicpk supplies this IC for technicians who work at board level on MediaTek-platform phones. Check the exact suffix printed on your failed chip before you order, because the MT6360 family ships in several variants.

Out of stock

15 People watching this product now!
Description

MT6360UP Power IC for Mobile Repair: MediaTek Companion PMIC

The MT6360UP power IC for mobile repair covers one of the busiest fault areas on MediaTek-platform boards: the charging and secondary power block. MediaTek documents the MT6360 as a multifunction device. It integrates a battery charger with OTG boost and BC1.2 detection, an ADC, flash and RGB LED drivers, two buck regulators, six LDO channels, and a Type-C port switch with a Power Delivery controller. The chip talks to the main processor over I2C. When it fails, you see a phone that refuses to charge, ignores the cable, or stays dead with a good battery. This listing gives you the verified function map so you can decide quickly at your repair bench.

What the MT6360 Integrates

The MT6360 works as a sub-PMIC next to the main SoC and its primary power IC. It takes the charger role, so it manages battery charging from the CHGIN input and supplies the OTG boost output when you plug an accessory into the phone. It also handles BC1.2 charger-type detection, which tells the phone what kind of USB source it sees. The Type-C port switch and Power Delivery controller sit inside the same package, so one chip influences both cable detection and fast-charge negotiation. Beyond charging, the IC drives two flash LED channels with torch and strobe modes, four RGB indicator channels, two buck regulators, and six LDO channels. A single failure here can knock out several unrelated functions at once, so look at the whole block before you blame the charging port.

Charging Input Protection and OTG Behavior

MediaTek’s driver bindings list selectable CHGIN overvoltage limits of 5.5 V, 6.5 V, 11 V, and 14.5 V, which shows the charger input handles higher-voltage adapters on platforms that support them. The same binding describes an OTG boost regulator that powers the USB VBUS line in host mode. This explains why a bad adapter, a liquid-damaged connector, or a short on VBUS often ends with the power IC on your bench. Measure VBUS resistance to ground first. A hard short on the input line points toward the charger block, and a clean line with a dead charge indicator points toward the Type-C controller or the I2C link. These checks save you from changing a chip that still works.

Replacing the MT6360UP Power IC on Your Repair Bench

Start with a microscope inspection of the pads around the IC for lifted traces, corrosion, and burnt flux. Apply flux, preheat the board from below, and lift the old chip with your hot air station at a controlled temperature. Clean the pads fully, check the footprint against the replacement IC, and reflow the new chip with fresh flux. Test charging, cable detection, and OTG before you close the phone. Treat IC change karna on this part with care, because the MT6360 family ships under several suffixes such as UP and PP. Match the suffix marked on the original chip and compare the layout before you reflow. If your phone shows a charging issue after the swap, recheck the surrounding capacitors and the Type-C connector before you suspect the new IC.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • MediaTek multifunction PMIC from the MT6360 family
  • Battery charger with OTG boost and BC1.2 detection
  • Type-C port switch with Power Delivery controller
  • Two buck regulators and six LDO channels
  • Two flash LED channels with torch and strobe modes
  • Four RGB indicator LED channels
  • Built-in ADC block
  • I2C interface to the main processor

Specifications

BrandMediaTek
ModelMT6360UP
CategoryPower IC / PMIC (charger and Type-C PD sub-PMIC)
CompatibilityMediaTek-platform boards that use the MT6360 sub-PMIC
Supported DevicesDevice-specific list not verified. Match the suffix and footprint against the original chip.
TechnologyMultifunction PMIC with battery charger, OTG boost, BC1.2 detection, ADC, 2-channel flash LED, 4-channel RGB LED, 2 buck regulators, 6 LDO channels, and Type-C PD controller. I2C host interface.

Common Repair Uses

  • Verified function-level workflows for this IC.
  • Fixing a charging issue after a short on the CHGIN or VBUS line
  • Recovering a dead phone where the charger block no longer responds
  • Restoring Type-C cable detection after connector or liquid damage
  • Repairing failed Power Delivery negotiation on supported boards
  • Fixing OTG that no longer powers USB accessories
  • Restoring flash and torch operation tied to the MT6360 LED driver
  • Restoring indicator LED function tied to the RGB channels
  • Replacing the IC after a hardware fault found with a multimeter and microscope

Compatible Devices

  • Verified scope is the MT6360 function family on MediaTek-platform boards. This IC is not a universal replacement and you must match the suffix and footprint.
  • MediaTek-platform smartphones that use the MT6360 as companion PMIC
  • Boards that use the MT6360 battery charger and OTG boost block
  • Boards that use the MT6360 Type-C port switch and PD controller
  • Boards that use the MT6360 flash LED and RGB LED drivers
  • Boards where the MT6360 buck regulators supply secondary rails
  • Boards where the MT6360 LDO channels supply secondary rails
  • Boards where the main SoC controls the MT6360 over I2C
  • Replacement for a failed MT6360 carrying the same UP suffix

FAQ

What is the product name?
The product name is MT6360UP Power IC.
What is the brand of this product?
The brand of this product is MediaTek.
What is the model of this product?
The model of this product is MT6360UP.
What is this product used for?
This product replaces a failed MT6360 sub-PMIC that handles battery charging, OTG boost, Type-C and Power Delivery control, buck and LDO rails, and LED drivers on MediaTek-platform boards.
Which devices are compatible with this product?
This product fits MediaTek-platform boards that use the MT6360 sub-PMIC. Match the suffix and footprint of your original chip, because model-level compatibility is not universal.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which faults point to a failed MT6360UP power IC?
Faults such as no charging, no cable detection, failed Type-C or Power Delivery negotiation, and OTG that no longer powers accessories point to this IC. Rule out the cable, connector, and battery first, then measure VBUS for a short before you change the chip.
Is the MT6360UP the same as the MT6360PP or other suffixes?
The MT6360 family ships under several suffixes, and sellers often list them together. Match the exact suffix printed on your original chip and compare the footprint before you reflow, because interchangeability between suffixes is not confirmed.