45 Degree 9mm Nozzle for Quick 861DW Hot Air Gun

₨ 1

45 Degree Hot Air Nozzle for 861DW Side Heating

This 9mm replacement sleeve adds a 45 degree curved angle to the air outlet of your Quick 861DW hot air gun. It slides over the original 9mm nozzle, so you keep your existing handpiece and only change the direction of the airflow. The angled tip lets you direct heat onto the side of a CPU or BGA chip when a straight nozzle cannot reach that edge. Technicians working under a microscope benefit most, because the handpiece can sit at a comfortable angle while the hot air still lands on the component. It is designed for the 861DW and the TR1300A. Choose the 9mm size only if your gun uses a 9mm outlet, and pick the 6mm or 7mm option for smaller outlets.

In stock

11 People watching this product now!
Description

45 Degree 9mm Nozzle for Quick 861DW Hot Air Gun

A straight hot air nozzle works well for most chips, but it runs into trouble when the component sits against a shield, a connector, or another part of the board. A 45 degree sleeve changes the direction of the airflow without replacing your whole handpiece. This 9mm version fits over the air outlet of a Quick 861DW gun, so you get angled heat using the hardware you already own. For a technician working on phone and laptop boards every day, that single change can save a lot of time at the bench.

Where a Straight Nozzle Falls Short

Most straight nozzles push hot air down onto the top of a component. That works when the chip is open on all sides, but CPUs and BGA packages often sit close to other parts. Heating the side of the package from above can be difficult, and the nearby parts may get hot before the target does. The curved sleeve moves the airflow to the side, so you can heat the edge of the chip directly. You keep the gun steady and reduce the guesswork about where the heat is landing.

Working Under a Microscope

When you use a microscope, you tend to lock your hand into a fixed angle. A straight nozzle then forces you to tilt the gun in a way that makes aiming awkward. The 45 degree sleeve lets the handpiece sit at a natural position while the airflow still reaches the chip. You can keep your eyes on the component through the lens and adjust the position of the gun with less strain. This setup suits precise work on small chips where accuracy matters more than speed.

Choosing the Right Size and Fit

The sleeve comes in several sizes, and the correct choice depends on the outlet of your gun. A 6mm, 7mm, or 9mm sleeve must match the original nozzle on your handpiece. Measure the outlet before you order, because a sleeve that is too large will not sit correctly. Once it is in place, check that it does not wobble. If the sleeve feels loose, you can pinch the middle section with pliers to tighten the grip. Snug fit matters because a loose sleeve can shift during a reflow cycle and change the target point of the heat.

Fitting and Handling Tips

Slide the sleeve onto the air outlet until it sits firmly, then test the airflow at a low setting before you start work. Keep the air outlet clear and maintain a safe distance from the board, as the Quick 861DW has a high-output heater. The metal parts get very hot during use, so hold the upper plastic housing when you handle the gun. After work, let the gun cool before you remove the sleeve, and always place the handpiece in its holder rather than switching it off immediately.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 45 degree curved angle for side heating
  • Fits over the original 9mm air gun outlet
  • Helps when aiming hot air under a microscope
  • Available in 6mm, 7mm, and 9mm sizes
  • Works with the Quick 861DW air outlet design

Specifications

Model45 Degree 9mm Sleeve
CategoryHot Air Gun Nozzles
CompatibilityQuick 861DW, Quick TR1300A
Technology45 degree curved angle nozzle sleeve

Common Repair Uses

  • Side heating of CPU and BGA chips where a straight nozzle cannot reach the component edge
  • Hot air work under a microscope when the handpiece must sit at an angle
  • Angled heating of chips in tight areas of phone and laptop logic boards

Compatible Devices

  • Quick 861DW hot air rework station, 9mm outlet version
  • Quick TR1300A hot air soldering station

FAQ

What is the product name?
The product name is 45 Degree 9mm Nozzle for Quick 861DW Hot Air Gun.
What is the brand of this product?
This sleeve is made for the Quick 861DW hot air gun, and the Quick brand is the platform it fits.
What is the model of this product?
The model of this product is the 45 degree 9mm nozzle sleeve.
What is this product used for?
This product is used to direct hot air at an angle for side heating of chips.
Which devices are compatible with this product?
This product is compatible with the Quick 861DW and Quick TR1300A hot air stations.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Does this sleeve fit a 6mm or 7mm gun?
No, this is the 9mm version. Choose the 6mm or 7mm sleeve that matches your gun’s air outlet size.
Can I use this nozzle under a microscope?
Yes, the angled design lets you keep the handpiece at a comfortable angle while the airflow still reaches the chip under the microscope.