i2C Q5 Blade Kit for CPU & IC Pry Scraper Knife
₨ 1
i2C Q5 Blade Kit for CPU & IC Work
The i2C Q5 blade kit gives your repair bench five dedicated blades on an aluminum alloy handle. Two right-angle chip pry blades, one 90° blade, and two edge-glue pry blades cover the full sequence on a phone motherboard. You pry the IC or CPU, scrape edge glue, and remove leftover tin from the pads. Carbon steel blades hold their edge through repeated heated-board sessions, so you stay in control when a bonded chip refuses to lift. Technicians in Pakistan use this CPU pry knife set on iPhone and Android boards for chip separation, underfill cleanup, and pad preparation before reballing. Mechanicpk supplies it as a compact, bench-ready kit.
Out of stock
Precision Chip Separation With the i2C Q5 Blade Kit
The i2C Q5 blade kit targets the step that decides whether a board survives a chip swap: separating a bonded IC or CPU without lifting pads. i2C builds the set around an aluminum alloy handle and five interchangeable carbon steel blades. Each blade carries a specific job in the mobile repair workflow. If you run a board-level bench in Pakistan, this kit replaces improvised scrapers and cut-down blades with tools shaped for the task.
Blade Geometry and Handle Design
Five blade profiles ship with the kit. Blades one and two use a right-angle chip pry profile. Blade one handles IC and CPU prying and glue removal. Blade two handles glue removal, tin removal, and layering work. Blade three uses a 90° profile for glue removal, tin removal, and edge-glue scraping. Blades four and five use an edge-glue pry profile for prying ICs and CPUs and scraping the glue line around them. The aluminum alloy handle keeps the weight low, and the retail pack measures 170 x 67 x 17 mm, so the case fits a bench drawer or a technician’s roll.
Where It Fits in the Repair Workflow
You reach for the Q5 after you heat the board and before you clean the pads. Preheat the PCB on a hot air station or preheater, slide the thinnest suitable blade at the chip edge, and work the bond loose in small steps. The edge-glue blades clear the epoxy ring that locks CPUs and NAND chips to the board. After the chip lifts, the 90° blade and the layering blade clear residual tin and underfill so the pads sit flat for reballing. Pair the kit with a microscope for pad inspection, a PCB holder for stable support, and a reballing kit for the next stage.
Common Faults This Kit Supports
Dead phone cases with a damaged CPU, NAND, or power IC often need a chip lifted cleanly. Hardware fault diagnosis on iPhone and Android boards leads to the same step: remove the suspect IC, clean the pads, and install a replacement. You also use the Q5 on charging issue and network issue repairs where a glued IC blocks access to the failing component. In each case, a blade that fits the chip edge lowers the risk of torn pads and lifted solder mask.
Why Technicians Choose This Tool
Buyers who already work at IC level look for blade steel that survives heat and a profile range that avoids swapping brands mid-job. The Q5 delivers five profiles in a single kit, which cuts the number of loose blades on your bench. The blades are thin enough to slide under chip edges and stiff enough to apply controlled leverage. Keep the blades clean after each session and wipe the tips so they stay sharp for the next board.
Mechanicpk stocks the i2C Q5 blade kit for repair shops, service centers, and training institutes across Pakistan that need a dependable CPU pry knife set alongside their hot air stations, soldering stations, and microscopes.
| Weight | 0.3 kg |
|---|
Key Features
- ✓Five blades in one kit for pry, scrape, and glue-removal jobs
- ✓Two right-angle chip pry blades
- ✓One 90° blade for glue, tin, and edge scraping
- ✓Two edge-glue pry blades for ICs and CPUs
- ✓Aluminum alloy handle with a lightweight build
- ✓Carbon steel blades for repeated use on heated boards
- ✓Suits iPhone and Android motherboard repair
- ✓Compact 170 x 67 x 17 mm pack for bench or travel storage
Specifications
| Brand | i2C |
|---|---|
| Model | Q5 Chip Repair Combination Kit |
| Category | Mobile Repair Tools – Blade Kits & Pry Knives |
| Compatibility | iPhone and Android motherboards |
| Technology | Carbon steel blade set with five profiles |
| Material | Aluminum alloy handle, carbon steel blades |
| Dimensions | 170 x 67 x 17 mm (package size) |
Common Repair Uses
- ✓Chip separation, glue and tin removal on mobile motherboards
- ✓Prying ICs off the board
- ✓Prying CPUs off the board
- ✓Removing edge glue around chips
- ✓Removing leftover tin from pads
- ✓Scraping underfill glue
- ✓Layering and board-level separation work
- ✓Pad cleaning before reballing
Compatible Devices
- ✓Universal blade kit for mobile phone motherboards, not model-specific
- ✓iPhone motherboards
- ✓Android phone motherboards
- ✓Phone CPU chips
- ✓NAND flash chips
- ✓Glued IC chips on mobile PCBs
- ✓BGA chips on mobile PCBs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How many blades come with the i2C Q5 kit and what does each one do?
Can I use the i2C Q5 blade kit to remove CPU and NAND chips from dead phone boards?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



