2UUL SA13PM Screen Sealing Adhesive iPhone 13 Pro Max 5pcs
₨ 900
2UUL SA13PM Sealing Adhesive for iPhone 13 Pro Max
The 2UUL SA13PM is a pre-cut, double-sided iPhone 13 Pro Max screen sealing adhesive built for display replacement jobs. Each 5-piece pack gives you a ready-shaped gasket for the 6.7-inch frame, so you skip hand-cutting and fitting errors. You clean the frame, lay the tape, then press it with a heat press to seal the screen bezel. 2UUL designed it to restore the phone’s IP67 airtightness and to block dust and moisture after repair. Repair shops and service centers in Pakistan use it to finish iPhone 13 Pro Max screen replacements with a clean, factory-style seal.
In stock
iPhone 13 Pro Max Screen Sealing Adhesive for Airtight Display Repairs
The 2UUL SA13PM iPhone 13 Pro Max screen sealing adhesive gives your bench a pre-cut double-sided gasket that matches the 6.7-inch frame of the iPhone 13 Pro Max. Every screen separation destroys the original seal, and a bare frame leaves the new display open to dust and moisture. This pack of five covers five display jobs without a blade, a ruler, or any guesswork around the bezel outline.
Why the Seal Matters After a Screen Replacement
Once you lift the display off an iPhone 13 Pro Max, the factory adhesive tears and stays stuck to the frame. A phone that goes back to the customer without a fresh seal invites dust under the glass and moisture at the edges. That turns a clean repair into a comeback with a new display problem. 2UUL positions this adhesive to restore the iPhone’s IP67 airtightness when you press it correctly, which gives you a repair you can stand behind. Pro Max customers expect the phone to feel sealed, and a proper gasket delivers that.
Pre-Cut Fit and Application Workflow
The tape arrives pre-cut for the 13 Pro Max frame, so it drops into place without trimming. You work in three steps. First, clean the frame and inspect it for deformation, because a bent frame stops any adhesive from seating flat. Second, apply the 2UUL tape along the frame. Third, press the new screen assembly with heat. 2UUL’s own instructions call for a heating pressure press, such as the 2UUL DA07 Mini Hot Press Station, to bond the tape and seal the bezel. The high-strength double-sided adhesive grips the frame and the display edge, which keeps the screen locked in place through daily use. Take your time on step one. Old adhesive residue under the new tape causes most failed seals.
Where It Fits in Your Repair Workflow
This part sits at the very end of an iPhone 13 Pro Max screen replacement. You separate the display, clean the frame under a microscope if you want a perfect surface, test the new screen, and then seal. Technicians who also handle board-level faults on the same phone, such as a charging issue or other hardware fault, reach for their soldering stations, hot air stations, and PCB holders earlier in the job. The sealing adhesive closes the repair after that work is done. Keep a few packs next to your multimeter and test box, because every screen job that ends in a reseal needs one fresh gasket.
Buying Notes for Pakistani Repair Shops
A 5-piece pack suits a busy workshop. You get enough gaskets for a batch of Pro Max screens and a spare for a re-do if a screen needs to come off again. The SA13PM code fits the iPhone 13 Pro Max only. Other iPhone 13 variants use their own 2UUL model codes, so match the code to the phone on your bench before you order. Service centers that handle iPhone 13 Pro Max screens every week benefit most, since the pre-cut shape shortens each job and keeps the finish consistent from one technician to the next. Pair the adhesive with a thermal press plate made for the iPhone 13 series when you want precise alignment during lamination.
| Weight | 0.100 kg |
|---|
Key Features
- ✓Pre-cut for the iPhone 13 Pro Max screen frame
- ✓High-strength double-sided adhesive
- ✓Heat press sealing for a tight bezel fit
- ✓Designed to restore IP67 airtightness
- ✓Blocks dust and moisture after screen replacement
- ✓No measuring, cutting, or trimming needed
- ✓Convenient 5-piece pack for batch repairs
- ✓Suited to repair shops and technicians
Specifications
| Brand | 2UUL |
|---|---|
| Model | SA13PM |
| Category | Screen Sealing Adhesive |
| Compatibility | iPhone 13 Pro Max |
| Supported Devices | iPhone 13 Pro Max (6.7-inch) |
| Technology | Pre-cut double-sided adhesive, heat press sealing |
| Weight | 100 g (5pcs pack) |
Common Repair Uses
- ✓Sealing the screen bezel after display replacement on the iPhone 13 Pro Max
- ✓iPhone 13 Pro Max screen replacement
- ✓Resealing the frame after LCD or OLED display separation
- ✓Restoring dust and moisture resistance after repair
- ✓Replacing adhesive torn during screen removal
- ✓Frame resealing during heat press lamination
- ✓Batch screen jobs in repair shops and service centers
Compatible Devices
- ✓Verified for the iPhone 13 Pro Max only (6.7-inch)
- ✓Apple iPhone 13 Pro Max
- ✓Model number A2484
- ✓Model number A2641
- ✓Model number A2643
- ✓Model number A2644
- ✓Model number A2645
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the 2UUL SA13PM fit the iPhone 13 or iPhone 13 Pro?
Do I need a heat press to install this screen sealing adhesive?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



