2UUL SA14P Screen Sealing Adhesive for iP14 Pro (5pcsPack)
₨ 900
iPhone 14 Pro Screen Reseal Adhesive
The 2UUL SA14P Screen Sealing Adhesive for iP14 Pro (5pcsPack) gives repair shops five pre-cut, double-sided adhesive frames shaped for the iPhone 14 Pro. You lay the adhesive on the cleaned frame, then press it with a heated press to bond the display and rebuild the seal around the screen edge. Technicians who open the iPhone 14 Pro for display replacement, charging port work, or board-level repair use it to close the phone cleanly instead of cutting generic tape by hand. The pack covers five reseals, which suits benches that handle several display jobs every week.
In stock
iPhone 14 Pro Screen Sealing Adhesive Built for Heat-Press Reseals
The 2UUL SA14P Screen Sealing Adhesive for iP14 Pro (5pcsPack) is an iPhone 14 Pro screen sealing adhesive that does one job: it closes the display frame after you open the phone. Every iPhone 14 Pro that comes in with a display problem, a charging issue, or a hardware fault on the logic board needs the screen lifted, and the factory seal does not survive that step. This pre-cut double-sided adhesive replaces it. Mechanicpk supplies the 2UUL SA14P as a five-piece pack, so a workshop covers several jobs from one purchase.
How the Pre-Cut Frame Fits Your Workflow
2UUL cuts the SA14P to the iPhone 14 Pro frame, so you skip measuring, trimming, and patching strips of generic tape. The supplier’s instructions give a three-step routine: clean the frame and check it for deformation, apply the tape, then heat-press the display down. A hot press such as the 2UUL DA07 Mini Hot Press Station, or another heated pressure press, handles the final fit. Heat and even pressure bond the adhesive to the frame and the display edge in one pass, which helps keep the gap consistent around the bezel and the Dynamic Island cutout. You still prepare the frame properly. Scrape off old adhesive residue, wipe the surface, and straighten any bend before the new adhesive goes on, because adhesive cannot hide a warped midframe.
Where It Sits in the iPhone 14 Pro Repair Process
Screen sealing comes at the end of an iPhone 14 Pro display or board repair, after testing. A typical job runs in this order: separate the display, disconnect the battery, fix the fault, then test the phone before you seal it. The tools around this step decide the quality of the result. A hot air station softens the old adhesive for removal, a microscope shows leftover residue along the frame edge, a PCB holder keeps the phone steady during board work, and a multimeter confirms the charging and power lines before you close everything up. Test first, seal last. Resealing a phone and then reopening it wastes adhesive and time, so a five-piece pack gives you margin for the occasional rework.
Display jobs dominate the volume. Cracked-screen replacements, OLED swaps, and front-side component repairs on the 14 Pro all end with the same sealing step, so one SKU moves steadily through a busy workshop. Service centers and repair shops in Pakistan that handle iPhone 14 Pro traffic benefit from holding spare packs, since this adhesive has no use outside its model.
What to Expect From the Seal
The adhesive restores the sealing layer between display and frame. The supplier states that heat-pressing with this adhesive brings back the iPhone’s water and dust resistance. That claim comes from the seller, not from an independent lab test. Treat a resealed phone as better protected against dust and splashes, and tell your customer that a third-party repair does not carry the original factory rating. Honest expectations protect your shop and keep returns low. 2UUL sells separate model-specific SA-series adhesives for other iPhone generations, so match the part to the exact model on your bench instead of trimming the iPhone 14 Pro piece to fit another phone.
| Weight | 0.100 kg |
|---|
Key Features
- ✓Pre-cut to the iPhone 14 Pro frame, so no measuring or trimming
- ✓Double-sided adhesive for bonding the display to the frame
- ✓Five pieces per pack for multiple repair jobs
- ✓Heat-press application for a firm, even bond
- ✓Works with the 2UUL DA07 Mini Hot Press Station or another heated pressure press
- ✓Supplier-stated airtightness restoration after a screen repair
- ✓Model-specific design for the iPhone 14 Pro
- ✓Fits front-opening workflows: display, battery, and charging port repairs
Specifications
| Brand | 2UUL |
|---|---|
| Model | SA14P (5pcs/pack) |
| Category | Screen Sealing Adhesive |
| Compatibility | iPhone 14 Pro |
| Supported Devices | iPhone 14 Pro |
| Technology | Pre-cut double-sided adhesive, heat-press application |
Common Repair Uses
- ✓Resealing the iPhone 14 Pro display frame after the phone has been opened
- ✓Display and OLED screen replacement on the iPhone 14 Pro
- ✓Resealing after charging port repair
- ✓Resealing after logic board or hardware fault repair
- ✓Closing the frame after battery replacement
- ✓Replacing worn or damaged factory adhesive around the display edge
- ✓Rework jobs where the first seal needs redoing
- ✓Restoring dust and splash protection after a display repair (supplier-stated purpose)
Compatible Devices
- ✓iPhone 14 Pro only (model-specific adhesive, not universal)
- ✓iPhone 14 Pro
- ✓iPhone 14 Pro model A2650
- ✓iPhone 14 Pro model A2889
- ✓iPhone 14 Pro model A2890
- ✓iPhone 14 Pro model A2892
- ✓iPhone 14 Pro model A2891
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Do I need a heat press to apply the 2UUL SA14P adhesive?
Can I use the SA14P on an iPhone 14 or iPhone 14 Pro Max?
Related products
RELIFE RL-004SA silicone pad – Anti-slip
In stock



