Mechanic iSm5 183℃ Specific Paste For Jumper Wire 3ml
₨ 700
Jumper Wire Solder Paste for Board Repair
Mechanic iSm5 183℃ Specific Paste For Jumper Wire gives technicians a purpose-made paste for fly line repairs on phone and laptop boards. The 3ml syringe ships with three application needles, so you place a small, controlled dot on the solder spot. Mechanic’s nano-compound formulation delivers high activity with moderate viscosity, and the iron tip tins the point in a single stamp. Use it for broken pad repair, BGA chip pad work, and jumper wire soldering on motherboards. Mechanicpk stocks it for repair shops and service centers across Pakistan that run jumper wire jobs daily.
In stock
Jumper Wire Solder Paste for Fly Line and Pad Repair
Mechanic iSm5 183℃ Specific Paste For Jumper Wire is a jumper wire solder paste for one repair job: anchoring hair-thin fly lines to damaged pads and traces on phone and laptop boards. Mechanic packs it in a 3ml syringe with three application needles, so you dispense a controlled dot instead of scooping paste from a jar. The nano-compound formulation delivers high activity with moderate viscosity, which means the paste wets the pad quickly and stays where you place it. If your bench handles dead phone cases, burnt traces, or lifted pads under BGA chips, this paste covers the step between cleaning the board and laying the wire.
What the 183℃ Rating Tells You Before You Buy
The 183℃ figure in the product name identifies the variant. Mechanic sells the same jumper wire paste family in a 138℃ version, the iSm3, so you choose the temperature that suits the board in front of you. A 183℃ joint tolerates more heat than a 138℃ joint, a point worth weighing when a fly line runs close to other components or near a connector that sees heat during later repairs. Set your soldering station to a temperature you control, tin the point, and keep the iron on the pad only as long as the paste needs to flow. If you also reball chips or reflow with a hot air station on the same board, plan the order of work so the airflow does not reach the finished jumper joint last. A steady, temperature-controlled iron gives this paste its best result, because the tip tins the point cleanly without scorching the pad beside it.
How iSm5 Fits the Jumper Wire Repair Workflow
Start by clearing the damaged area under a microscope, then expose the trace end or pad you plan to reconnect. Pick up a small amount of paste and place it on the solder spot. According to Mechanic’s product description, the iron tip tins the point in a single stamp, so you move straight to placing the jumper wire on the tinned point and finishing the joint. Repeat the same method for the second end of the fly line, then trim the wire and check that the joint sits flat against the board so nothing lifts when you refit the shield or the frame. Technicians use this fly line repair routine for charging issue repairs where a charging port pad lifted, for display problem repairs on damaged connector pads, for iPhone fingerprint flex repair, and for CPU or BGA chip pad rebuilds on laptop motherboards. A broken trace can also sit behind a boot loop issue or a hang on logo fault, so a clean jumper often revives a board you were ready to write off. Hold the board in a PCB holder so both hands stay free, and confirm every joint with a multimeter continuity check before you reassemble the device.
What You Get in the Pack and Who Should Buy It
Each unit includes one 3ml syringe of paste and three application needles, which gives your bench spare dispensing tips when one clogs or bends. Repair shop owners stock it as a consumable next to flux, solder wire, and wick, because every jumper wire job uses only a little paste. Keeping a syringe at each repair station saves your technicians from sharing one tube across benches and losing time mid-repair. Board-level technicians reach for it daily, GSM technicians use it when a software fix cannot recover a hardware fault, and training institutes use it to teach fly line technique. The paste is universal rather than device-specific, so one syringe serves any phone, laptop, or PCB where a jumper wire repair makes sense. Mechanicpk lists the rest of the bench alongside it: soldering stations, hot air stations, microscopes, multimeters, PCB holders, and reballing kits, plus test boxes and ISP pinout tools for the software side of the job.
| Weight | 0.5 kg |
|---|
Key Features
- ✓3ml syringe for controlled dot dispensing
- ✓3 application needles included
- ✓183℃ variant of the Mechanic jumper wire paste family
- ✓Nano-compound formulation
- ✓High activity for quick pad wetting
- ✓Moderate viscosity that stays on the solder spot
- ✓Iron tip tins the point in a single stamp
- ✓Purpose-made for fly line and jumper wire repair on phone, laptop, and PCB boards
Specifications
| Brand | Mechanic |
|---|---|
| Model | iSm5 (3ml syringe, 3 application needles included) |
| Category | Solder Paste and Flux |
| Compatibility | Universal – not device-specific |
| Technology | Nano-compound jumper wire solder paste, 183℃ variant |
Common Repair Uses
- ✓Jumper wire and fly line soldering on damaged pads and traces
- ✓Fly line jumper wire soldering on broken traces
- ✓Lifted pad repair on charging port areas
- ✓Connector pad repair for display problem faults
- ✓iPhone fingerprint flex repair
- ✓BGA chip pad rebuild
- ✓CPU pad repair on laptop motherboards
- ✓Tinning wire ends and pads before jumper placement
Compatible Devices
- ✓Universal – not device-specific; verified use scope covers phone, laptop, and PCB boards
- ✓Android and other smartphone motherboards
- ✓iPhone logic boards
- ✓iPhone fingerprint flex repair
- ✓Laptop motherboards
- ✓CPU and BGA chip pads
- ✓General PCB boards that need jumper wire repair
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What is the difference between Mechanic iSm3 and iSm5 jumper wire paste?
How do you apply iSm5 paste for fly line soldering on a dead phone board?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock



