Mechanic SU7 Black UV Curing Masking Paste 10ml
₨ 350
Black UV Solder Mask for Board Repair
Mechanic SU7 Black UV Curing Masking Paste is a 10ml UV-curable solder mask ink that insulates jumper wires, repaired traces and exposed copper on phone logic boards. You apply it, spread it under a transparent film and cure it with a UV lamp or sunlight in a few minutes. After jumper lagana, trace repair or BGA rework, the cured coat protects copper from moisture and helps prevent shorting and arcing. It gives your repair bench a clean, final insulation step with a dark finish. Order it from Mechanicpk for your workshop or service center in Pakistan.
In stock
Black UV Curing Masking Paste for Mobile Board Repair
Mechanic SU7 Black UV Curing Masking Paste gives board-level technicians a controlled way to finish a repair. After you lay a jumper wire, rebuild a damaged trace or clean up a reballed area, the exposed copper stays vulnerable to moisture, flux residue and accidental contact. This black UV curing masking paste is a one-component solder mask ink from Mechanic. You apply it by hand, level it under a transparent film and harden it with a UV lamp or sunlight. It sits in the consumables group beside your flux, solder paste and wick, and it closes the repair once the soldering stage ends.
Where the Paste Fits in Your Repair Workflow
A board repair ends with insulation, and the SU7 handles that step. After you finish jumper lagana on a lifted pad, you coat the joint and the wire route with the paste. You cover it with transparent mask film so it spreads evenly, then expose it to UV light or sun for a few minutes. The cured layer insulates the repair against shorting and arcing and shields the copper trace from corrosion and moisture. You wash away uncured excess with gasoline or an oil-based solvent, so the neighbouring pads and components stay clean. Run a multimeter continuity check before you coat, because the paste seals the repair and you want the connection confirmed first.
Black Finish for Hardware Fault Repairs
Technicians use this UV solder mask for mobile repair after the hardware fault is already fixed. A charging issue repair often ends with a rebuilt charging port pad. A display problem repair may leave a patched connector trace. A dead phone brought back with a rebuilt power line needs its jumper wires locked down before the board goes back into the frame. The black coat gives these repairs a finished look and protects each bridge from contact. Technicians who wire ISP points for eMMC work use the same step to insulate and secure fine jumper wires. This jumper wire insulation role pairs naturally with your microscope for precise placement and your PCB holder for a steady board. The hot air station and reballing kit handle the rework stage before you coat.
Why Repair Shops Stock It
The SU7 uses a UV or sunlight cure, so your bench needs only a UV lamp or a sunny window, with no oven and no thermal cure step. The 10ml size covers a long run of jumper and trace repairs, which makes it a practical consumable for busy service centers. Mechanic is a familiar brand in the mobile repair industry, and technicians in Pakistan already recognise its solder mask range. Black stays a useful colour choice for boards where you want the repaired area to blend in rather than stand out. Pair it with your soldering station, flux and test box, and your insulation step becomes as repeatable as the rest of your workflow. Browse the related categories on Mechanicpk to complete your bench with ISP pinout tools, eMMC programmers, UFS adapters, multimeters and reballing kits.
| Weight | 0.20 kg |
|---|
Key Features
- ✓Single-component UV-curable solder mask ink
- ✓Cures under UV light or strong sunlight
- ✓Black colour for a clean finished repair
- ✓10ml net content for repeated jumper and trace jobs
- ✓Insulates PCB traces against shorting and arcing
- ✓Protects copper from moisture and corrosion
- ✓Washes off uncured excess with gasoline or oil-based solvent
- ✓Works on mobile phone logic boards and general PCBs
Specifications
| Brand | Mechanic |
|---|---|
| Model | SU7 |
| Category | UV Solder Mask / Masking Paste |
| Compatibility | Universal, not device-specific |
| Supported Devices | Mobile phone logic boards and general electronics PCBs |
| Technology | UV-curable solder mask ink, cures under UV light or sunlight |
| Material | Solder mask ink (viscous liquid), black, 10ml |
Common Repair Uses
- ✓Real-world repair scenarios where this paste finishes the job
- ✓Insulating jumper wires after jumper lagana
- ✓Covering repaired PCB traces
- ✓Protecting exposed copper from moisture and corrosion
- ✓Preventing shorting and arcing near repaired joints
- ✓Sealing the area after BGA rework
- ✓Replacing damaged solder mask on small board areas
- ✓Locking down ISP jumper wires on eMMC repairs
- ✓Finishing charging port and connector pad repairs
Compatible Devices
- ✓Universal PCB repair scope, not limited to specific phone models
- ✓Smartphone logic boards (brand-independent)
- ✓Android phone motherboards
- ✓iPhone logic boards
- ✓Tablet motherboards
- ✓Laptop motherboards
- ✓General electronics PCBs
- ✓Boards with jumper wire repairs
- ✓Boards after BGA rework
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How do you cure Mechanic SU7 black UV masking paste?
How do you clean off uncured SU7 solder mask paste?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



