Mechanic XGZ40 Solder Paste 183°C Sn63/Pb37 35g
₨ 799
XGZ40 Sn63/Pb37 Solder Paste
Mechanic XGZ40 solder paste packs a eutectic Sn63/Pb37 alloy into a 35g, 10cc syringe built for BGA, SMD and PCB rework. The alloy melts at a single fixed point of 183°C, so the paste moves cleanly from solid to liquid without a mushy transition. Its high viscosity keeps the paste in place while you heat, and the syringe lets you dispense straight onto the pad with no stencil or spatula prep. Repair shops and service centers across Pakistan use it for IC reattachment, pad tinning and board-level repair where predictable reflow matters on every joint.
Out of stock
Mechanic XGZ40 Solder Paste for Precision BGA and SMD Rework
Mechanic XGZ40 solder paste gives your repair bench a eutectic Sn63/Pb37 alloy in a ready-to-dispense 35g syringe. The alloy combines 63% tin with 37% lead, so every particle melts at one fixed temperature: 183°C. That behavior matters when you reflow a BGA IC or reattach an SMD component on a crowded mobile board and need each joint to form the same way, every time. The paste suspends fine solder microparticles in flux, which wets clean pads and pulls components into alignment as the alloy liquefies.
Eutectic Alloy Behavior at 183°C
Sn63/Pb37 is the classic eutectic composition in electronics rework. A eutectic alloy skips the plastic phase that non-eutectic alloys pass through, so the joint goes from liquid to solid in a single step once you pull the heat away. You get shiny, consistent joints and less risk of a disturbed joint while the solder cools. The 183°C melting point also sits well below common lead-free alloys, so the board and its neighboring components see less thermal stress during reflow. When you work on a board that already carries leaded solder, matching the alloy keeps the reflow profile predictable.
Syringe Dispensing for Fast Bench Work
The 10cc syringe holds 35g of paste, and you apply it directly to the pad without preparing a stencil. Clean and degrease the board first, set the PCB flat, squeeze a small amount onto the soldering area and seat the component. The paste has high viscosity, so it holds its position instead of spreading while heat builds. As you heat the joint, the flux boils off and the paste shrinks, then the solder particles melt and fuse. The joint solidifies within seconds after you remove the heat. Store the syringe in cool, dry conditions and keep the cap on between jobs.
Where XGZ40 Fits in Your Repair Workflow
You reach for this paste during IC change karna jobs, BGA pad tinning, SMD component reattachment and PCB pad repair. It suits the hardware fault work that follows a dead phone diagnosis, where you replace a power IC, charging IC or other board-level part and need clean, repeatable reflow. Pair it with a hot air station for controlled heating, a soldering station for finishing touches, a reballing kit for BGA work, a PCB holder to keep the board steady and a microscope to inspect the result. The paste supports surface soldering and repair of PCB, BGA, SMD and PGA components, so one syringe covers most of the reflow tasks on a typical repair bench.
The alloy contains lead. Work in a ventilated space, wash your hands after handling and keep the paste away from food. Because of the lead content, the paste does not suit commercial products that must meet RoHS regulations; it belongs in repair and rework environments. Buy XGZ40 for your workshop when you want a proven eutectic alloy, a precise syringe format and a melting point that keeps your hot air settings predictable across everyday board repairs.
| Weight | 0.35 kg |
|---|
Key Features
- ✓Eutectic Sn63/Pb37 alloy with a single 183°C melting point
- ✓35g net weight in a 10cc syringe
- ✓High viscosity holds the paste in place while heat builds
- ✓Fine solder microparticles in flux for clean wetting
- ✓Suits PCB, BGA, SMD and PGA soldering and repair
- ✓Direct syringe dispensing with no stencil or spatula prep
- ✓Solidifies within seconds after you remove the heat
- ✓Reduces thermal stress compared with higher-melting lead-free alloys
Specifications
| Brand | Mechanic |
|---|---|
| Model | XG-Z40 |
| Category | Solder Paste |
| Compatibility | Universal, not device-specific |
| Technology | Eutectic Sn63/Pb37 leaded alloy with flux, 183°C melting point |
| Material | Sn63/Pb37 solder alloy with flux |
| Weight | 35g net (10cc syringe) |
Common Repair Uses
- ✓Board-level rework where you need precise, repeatable reflow with a eutectic leaded paste.
- ✓BGA IC reattachment
- ✓BGA pad tinning before reballing
- ✓SMD component soldering and replacement
- ✓IC change karna on dead phone boards
- ✓Charging IC and power IC replacement
- ✓PCB pad and joint repair
- ✓Hot air station reflow work
- ✓Hardware fault repair on mobile logic boards
Compatible Devices
- ✓Universal solder paste for PCB-level repair. It is not tied to specific phone models, brands or chipsets, and it suits any board that uses leaded or mixed-alloy joints.
- ✓BGA ICs on mobile phone logic boards
- ✓SMD components on mobile phone PCBs
- ✓PGA components
- ✓PCB pads and traces on phone boards
- ✓Power and charging ICs on board
- ✓Surface-mount parts on laptop and general electronics boards
- ✓Boards that already use Sn63/Pb37 leaded solder
- ✓Surface-mount rework on repair-bench PCBs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What is the melting point of Mechanic XGZ40 solder paste?
Is Mechanic XGZ40 leaded or lead-free?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock



