Mijing AR-2015 Alpha Desoldering Wick 5pcs/Box

₨ 1,499

Mijing AR-2015 Alpha Tin-Absorbing Wire

The Mijing AR-2015 desoldering wick gives your repair bench a high-purity copper braid for lifting leftover solder off motherboard pads. The oxidation-resistant coating and low-residue design keep pads clean after you remove an IC, so the next chip sits flat. The braid stays flexible enough to reach tight areas around neighbouring components without stressing the PCB. Each box contains five pieces of Alpha tin-absorbing wire, which covers daily pad-cleaning work in a busy workshop. Pair it with a hot air station or a soldering station and flux to finish IC change jobs and clear solder bridges on mobile phone boards.

In stock

13 People watching this product now!
Description

Mijing AR-2015 Desoldering Wick for Clean IC Pads

The Mijing AR-2015 desoldering wick is a copper braid built for one task: pulling molten solder off motherboard pads so the next IC lands on a flat, clean surface. Each box holds five pieces of Alpha tin-absorbing wire, so one order stocks your bench for the week. You reach for it on a dead phone that needs an IC change karna, and again on a board with solder bridges after a rushed rework. It clears excess tin with far less bulk than a desoldering pump, which matters on dense mobile boards. Mechanicpk supplies the AR-2015 to repair shops that want a consistent consumable at every bench.

Braid Construction and Absorption Behavior

The AR-2015 uses high-purity copper wire woven into a flat braid. Copper conducts heat quickly, so molten solder travels into the weave as soon as your iron tip touches the wick. The braid carries an oxidation-resistant coating that helps it keep absorbing tin instead of dulling after a few passes. A low-residue, fluorine-free design leaves the pad surface cleaner than a bare braid, which shortens your cleanup before reballing or re-tinning.

The braid also stays flexible. You can bend it around the edge of a shield frame or along a row of pads beside small passives and press it flat without gouging the surface. That control protects the pad and the solder mask when you work near a charging IC or power IC.

Where It Fits in Your Rework Workflow

Pad cleaning sits in the middle of almost every board-level repair. After your hot air station lifts an IC, residual solder remains on the pads. Lay the AR-2015 over that solder, press your soldering iron on top, and drag slowly. The braid draws the tin up and leaves a level surface for inspection under your microscope. Check the pads, then move on to the next step: tinning, placing a new chip, or reballing with your stencil and reballing kit.

The same technique clears bridges between fine-pitch pins and removes excess solder after you lift a jumper lagana attempt that went wrong. Hold the board in a PCB holder so both hands stay free, and keep a multimeter nearby to confirm continuity once the pads are clean. Boards that arrive for hang on logo or charging issue faults often need this cleanup after the faulty component comes off.

Handling Tips for Pad-Safe Cleanup

Use fresh braid for each pass. Once a section turns silver and stiff, cut it off and expose clean copper. Keep the iron moving and avoid long dwell time on one pad, because extended heat risks lifting traces on thin boards. Add a small amount of flux when pads carry stubborn solder, then wipe the area with isopropyl alcohol after cleaning to remove flux and inspect the finish.

Store the remaining pieces in the box away from moisture so the copper stays bright. Technicians who use the AR-2015 as a standard bench consumable also benefit from predictable results, since every piece in the box behaves the same way across IC changes, pad repair, and general board cleaning.

Additional information
Weight0.5 kg
Q & A
Please login to post questions

Key Features

  • High-purity copper braid for fast solder absorption
  • Oxidation-resistant coating for steadier performance
  • Low-residue design for cleaner pads
  • Fluorine-free construction
  • Flexible braid that fits tight board areas
  • Gentle on pads and nearby components
  • Five pieces per box for daily workshop use
  • Built for motherboard IC chip cleaning

Specifications

BrandMijing
ModelAR-2015 Alpha
CategoryDesoldering Wick / Tin-Absorbing Wire
CompatibilityUniversal – not device-specific
TechnologyOxidation-resistant coating, low-residue, fluorine-free
MaterialHigh-purity copper braid
Quantity5 pieces per box

Common Repair Uses

  • Cleaning residual solder from motherboard pads and IC footprints during mobile phone and PCB repair
  • Cleaning pads after IC removal
  • Preparing pads before reballing
  • Removing solder bridges between pins
  • Levelling pads before fitting a new chip
  • Clearing excess solder after failed rework
  • Pad cleanup on charging IC and power IC areas
  • Cleaning pads around shield frames
  • General motherboard cleaning during PCB repair

Compatible Devices

  • Universal consumable – works on any PCB solder pad, not limited to specific phone models
  • Android smartphone motherboards
  • iPhone logic boards
  • Tablet motherboards
  • Feature phone boards
  • Sub-boards and small PCB modules
  • IC chip pads on mobile phone motherboards
  • Charging and power section pads
  • General electronics PCBs

FAQ

What is the product name?
The product name is Mijing AR-2015 Alpha Tin-Absorbing Wire (5pcs/box).
What is the brand of this product?
The brand of this product is Mijing.
What is the model of this product?
The model of this product is AR-2015 Alpha.
What is this product used for?
This product is used for removing leftover solder from motherboard pads and IC footprints during mobile phone and PCB repair.
Which devices are compatible with this product?
This product is a universal consumable and works on any PCB solder pad, including mobile phone motherboards.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
How do I clean IC pads with the Mijing AR-2015 without lifting them?
Lay the wick flat over the solder, press your soldering iron on top, and drag slowly. Add flux for stubborn solder, keep the iron moving, and cut off each used section before the next pass.
What do I need alongside the AR-2015 wick for a full IC change?
You need a soldering iron or soldering station for the wick, a hot air station to lift the chip, flux, and a microscope to inspect the pads before you fit the new IC.