MT6372CP Power IC – MediaTek Charging & Backlight SubPMIC

₨ 500

MT6372CP Power IC for MediaTek Board Repair

The MT6372CP Power IC is a MediaTek SubPMIC from the MT6370 family. It sits next to the main PMIC on MediaTek-platform phone boards. The family combines several blocks in one package: the single-cell battery charger, the USB Type-C and PD controller, the flash LED and RGB drivers, the WLED backlight driver, display bias, and a general LDO. When this chip fails, you see charging issues, a dark screen with a live display, a dead flash, or a short on the VBUS line. Mechanicpk supplies the exact MT6372CP marking, so your IC change matches the original part and the board’s firmware.

12 People watching this product now!
Description

MT6372CP Power IC: MediaTek SubPMIC for Charging, Flash and Backlight Rails

The MT6372CP Power IC is a MediaTek sub power management IC (SubPMIC) that handles the charging path and the light and display rails on MediaTek-platform phone boards. The chip belongs to the MT6370 family. That family integrates a single-cell Li-ion/Li-polymer switching charger, a USB Type-C and Power Delivery controller, dual flash LED current sources, an RGB LED driver, a WLED backlight driver, a display bias driver, and a general-purpose LDO. The mainline Linux kernel lists MT6372 as its own compatible inside the MT6370 driver and gives it a wider 16384-step backlight control range. When one of these blocks fails, the phone develops a hardware fault that no software flash can fix. Mechanicpk stocks this part for technicians who diagnose at board level and need the exact marking for a clean IC change.

Where the MT6372 Charging IC Sits in the Power Tree

USB input reaches the board through the Type-C port and lands on the MT6372 charging IC before it gets anywhere near the battery. The charger block regulates battery voltage and current with high accuracy and limits average input current. It also senses battery temperature, protects against over-temperature, and runs BC1.2 DPDM detection so it can identify the type of adapter connected. An internal ADC monitors nine channels, covering VBUS, VBAT, VSYS, input current, battery current, and junction temperature. The phone’s charging software reads every one of these values through this chip, so a damaged SubPMIC can make good battery and port hardware look faulty. The same package also drives the backlight string, the positive and negative display bias rails, the flash LEDs, and the vibrator LDO. A single failed chip can therefore explain several symptoms that seem unrelated.

Diagnosing an MT6372CP Power IC Fault on the Bench

Begin with the symptom pattern. Each of the following points toward this SubPMIC:

  • Charging issue: the phone does not charge, charges slowly, or shows a charging animation while the battery percentage stays fixed.
  • Display problem: the touch works and the image is faintly visible under a torch, but the backlight stays off.
  • Flash or vibrator: the flash LED or vibrator motor stops working after a liquid or short-circuit event.
  • Dead phone: a short on VBUS or VSYS shows up on a DC power supply at the moment you connect it.

Run diode-mode readings with a multimeter around the IC and compare them against a known-good board. Inject low voltage on the shorted rail and locate the heat with rosin or a thermal camera. Inspect the area under a stereo microscope for cracked balls, corrosion, or burnt passives before you decide to replace the chip. This order stops you from swapping a healthy IC when the real fault is a shorted capacitor next to it.

Replacement Workflow and Matching the Correct Variant

Set your hot air station to a controlled profile and apply quality flux. Lift the old chip evenly so the pads underneath stay intact. Clean the pads with solder wick and a fine-tip soldering station, then reball or level the pads with a reballing kit if they need it. Hold the board in a PCB holder so the heat stays stable while you seat the new MT6372CP Power IC.

Match the marking exactly. The kernel treats MT6370/MT6371 and MT6372 as separate variants with different backlight handling, so do not assume a cross-substitution will work. After replacement, check charging current with a USB tester and confirm backlight brightness across its full range. Then test the flash, the vibrator, and fast-charge negotiation before you close the phone.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Genuine MT6372CP marking for exact-match IC replacement
  • Integrated single-cell Li-ion/Li-polymer switching charger
  • USB Type-C and Power Delivery controller in the same package
  • Dual flash LED current sources supporting torch and strobe modes
  • WLED backlight driver with 16384-step dimming support on MT6372
  • Display bias outputs plus a general LDO commonly used for the vibrator
  • Nine-channel ADC monitoring VBUS, VBAT, VSYS, currents, and temperature
  • Over-temperature protection and battery temperature sensing in the charger

Specifications

BrandMediaTek
ModelMT6372CP
CategoryPower Management IC (SubPMIC)
CompatibilityMediaTek-platform boards designed for the MT6372 SubPMIC
TechnologyMT6370-family SubPMIC — switching battery charger, USB Type-C/PD controller, flash LED driver, RGB LED driver, WLED backlight driver, display bias, general LDO

Common Repair Uses

  • No-charging or fake-charging faults traced to the SubPMIC
  • Charger-not-detected faults caused by a failed USB input/detection stage
  • Short on the VBUS or VSYS line after liquid damage or a bad adapter
  • Backlight-off faults where the display and touch still work
  • Display bias failure causing a blank or abnormal display
  • Flash LED not working in torch or camera flash mode
  • Vibrator dead because of a failed LDO output
  • Heat near the SubPMIC area during charging

Compatible Devices

  • Chipset-family level. The fit is decided by the IC marking on the board, not by the phone brand.
  • MediaTek-platform smartphones whose board carries an MT6372-marked SubPMIC
  • MediaTek-platform tablets and portable devices built on the MT6372 SubPMIC design
  • Direct replacement for MT6372CP-marked ICs
  • Boards that pair a MediaTek main PMIC with an MT6372 sub-PMIC for charging and display rails

FAQ

What is the product name?
The product name is MT6372CP Power IC.
What is the brand of this product?
The brand of this product is MediaTek.
What is the model of this product?
The model of this product is MT6372CP.
What is this product used for?
This product is used for replacing a faulty MT6372 SubPMIC that controls charging, backlight, display bias, flash LED, and vibrator power on MediaTek-platform phone boards.
Which devices are compatible with this product?
This product is compatible with MediaTek-platform phones and tablets whose board carries an MT6372-marked SubPMIC.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can I replace an MT6372 IC with an MT6370 IC?
No direct swap is recommended. The MT6370/MT6371 and MT6372 are separate variants with different backlight handling, so you should replace the chip with the same MT6372 marking found on the board.
Which faults show that the MT6372 charging IC has failed?
Common signs include no charging or fake charging, the charger not being detected, a short on VBUS or VSYS, no backlight while the display still works, a dead flash LED, and a dead vibrator.