PH000 1.5mm Phillips Screwdriver by Mechanic iMini
₨ 400
PH000 1.5mm Phillips Screwdriver for Smartphone Repair
The Mechanic iMini Phillips 1.5 is a PH000 precision screwdriver sized for the 1.5mm Phillips fasteners found in smartphone housings, brackets, and shield plates. It pairs a chrome-molybdenum steel bit with an aluminum alloy handle, which gives you a rigid grip for breaking loose tight screws without flexing. The magnetic tip holds small screws during removal, so fewer fasteners disappear into the repair bench. Use it for back cover removal, battery bracket work, and board preparation before diagnostics or reballing. It fills the 1.5mm screw class that finer and larger drivers leave uncovered.
In stock
PH000 1.5mm Phillips Screwdriver: Built for Precision Phone Repair
Stripped screw heads cost time, and sometimes they cost the device itself. This PH000 1.5mm Phillips screwdriver gives you a tip sized for the 1.5mm screw class used across smartphone assemblies. The Mechanic iMini Phillips 1.5 reduces cam-out, the slip that pushes the bit out of the screw head under torque and rounds the fastener. Its chrome-molybdenum bit is chosen for wear resistance, and the aluminum alloy handle transfers turning force directly to the tip. Technicians on busy benches benefit from a driver that stays accurate through a full shift of disassembly and reassembly.
Where PH000 Screws Appear in Phone Repair
Many smartphone designs use 1.5mm Phillips screws to secure bracket, battery connector, and shield plate assemblies. You encounter them when you open a back cover on a screw-fastened housing, remove a battery bracket before a battery swap, or lift a camera module for lens replacement. Shield covers on the logic board often use the same fastener class, so you need the right tip before any board-level diagnostic or reballing work. SIM tray brackets and charging port brackets on many Android devices follow the same pattern. Count the fasteners before you remove the first one, and note their positions so reassembly goes faster. Work on a clean mat, because dust in the screw head reduces bit engagement. Before you apply torque, seat the bit fully in the head, since a loose fit causes the rounding that makes removal harder later.
Chrome-Molybdenum Bit and Aluminum Handle on the Bench
This driver pairs a chrome-molybdenum steel bit with an aluminum alloy handle, two materials that suit precision work in different ways. Chrome-molybdenum steel holds its profile through repeated insertions, so the tip stays true longer than softer alloys do. The aluminum handle stays light during extended sessions and feels rigid under turning force, so less effort goes into flexing the grip. That rigidity helps when you break loose a screw tightened at the factory or one corroded after water exposure, a frequent case in phones that reach Pakistani repair shops. The anti-slip handle surface keeps your grip steady whether your hands are dry or damp. That combination suits technicians who work through many devices each week and need a driver that holds up. Store the driver with the bit fully seated to protect the tip from side damage.
Magnetic Tip Workflow on Your Repair Bench
The magnetic tip changes how you remove and reinstall small screws. A 1.5mm screw can fall into a keyboard tray, a mat fold, or a gap in the chassis within seconds. The tip holds the fastener while you lift it from the housing, so you place it directly into the next bracket without searching the bench. The magnetic hold also keeps the screw aligned during the first turns, which speeds reinstalling shields and brackets. Across a full shift of flashing, reballing, and reassembly, those saved seconds add up to real time. Treat a labeled screw tray as part of the process, not an extra step, because it stops one missing screw from delaying the whole job.
| Weight | 0.11 kg |
|---|
Key Features
- ✓Chrome-molybdenum steel bit for wear resistance
- ✓Aluminum alloy handle for a light, rigid grip
- ✓Magnetic tip holds 1.5mm screws during removal and installation
- ✓Anti-slip handle surface for steady grip during long sessions
- ✓PH000 sizing for the 1.5mm Phillips screw class
- ✓Compact form suited to tight internal repair spaces
- ✓Lightweight body at 0.11 kg
- ✓Fits a precision toolkit alongside finer and larger Phillips drivers
Specifications
| Brand | Mechanic |
|---|---|
| Model | iMini Series Phillips 1.5 (PH000) |
| Category | Mobile Soldering Accessories |
| Compatibility | Universal, not device-specific (PH000 1.5mm Phillips screws) |
| Technology | Magnetic tip |
| Material | Chrome-molybdenum steel bit, aluminum alloy handle |
| Weight | 0.11 kg |
Common Repair Uses
- ✓Back cover and housing disassembly on screw-fastened phones
- ✓Battery connector bracket removal before battery replacement
- ✓Camera module removal for lens or sensor replacement
- ✓Shield plate removal before board-level diagnostics
- ✓SIM tray bracket removal
- ✓Speaker and charging port bracket screw removal
- ✓Reassembly of brackets and shields without losing fasteners
- ✓Board preparation before IC-level diagnostic or reballing work
Compatible Devices
- ✓Universal, not device-specific. Any device fastened with PH000 (1.5mm) Phillips screws.
- ✓Back cover screws on screw-fastened smartphone housings
- ✓Battery connector bracket screws
- ✓Camera module mounting screws
- ✓Logic board shield plate screws where PH000 applies
- ✓SIM tray bracket screws
- ✓Charging port bracket screws
- ✓Speaker module screws
- ✓Other small electronics using PH000 1.5mm Phillips fasteners
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is PH000 the right size for smartphone bracket and shield screws?
Which screws does this driver not cover?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



