Qianli Bumblebee Stencil (QS41) SAM2 Note Series
₨ 600
Qianli QS41 Stencil for Note 4 CPU Reballing
The Qianli Bumblebee Stencil (QS41) SAM2 Note Series gives your bench a dedicated reballing template for the Samsung Galaxy Note 4 and its Qualcomm APQ8084 platform. Qianli lists the pattern for the CPU, BGA529 and eMCP footprint under its Universal Series, with square, round-angle openings made for BGA work. You use it after lifting the chip with a hot air station, so the CPU goes back with a clean, evenly spaced ball array. Repair shops in Pakistan stock it for Note 4 boards that arrive dead, hang on logo, or fail after a CPU hardware fault.
In stock
Qianli QS41 BGA Stencil for Samsung Note 4 APQ8084 Reballing
The Qianli Bumblebee Stencil (QS41) SAM2 Note Series is a Qianli QS41 BGA stencil for Samsung Note 4 boards built around the Qualcomm APQ8084 platform. It covers the CPU, BGA529 and eMCP footprint that Qianli groups under its Universal Series, so you reball the chip from one matched template instead of improvising with a generic plate. When a Note 4 reaches your bench with a hardware fault, this stencil gives the lifted CPU a clean, evenly spaced set of solder balls before it returns to the board.
What the QS41 Pattern Covers
Qianli tags the QS41 for the Samsung Galaxy Note 4 and the Qualcomm APQ8084 platform, covering the CPU, BGA529 and eMCP footprint inside its Universal Series. That scope matters when you buy. This plate matches one chipset family, so you choose it by the APQ8084 on your board, not by guesswork from the phone’s outer model. The openings are square holes with rounded angles, the pattern Qianli uses across its Bumblebee BGA range. Each opening sits where a ball belongs, so the paste or ball you place lands on the pad position instead of drifting. The supplier listing describes the stencil as sturdy, precise and durable over repeated jobs, which suits a shop that reballs Note 4 boards often.
Where It Sits in a Note 4 Repair Workflow
A Note 4 reaches your bench with a dead phone symptom, a hang on logo, a boot loop issue, or a charging issue that software cannot explain. Once multimeter readings and a test box check point to the CPU joints, the chip comes off. You lift it with a hot air station, clean the pads with a soldering station and flux, and clamp the board in a PCB holder. Under a microscope you inspect the pads, then align the QS41 over the chip, fill the openings, and lift the template away. Reflow forms the balls, and the CPU goes back on the board. If the same board needs storage work afterward, your eMMC programmer and ISP pinout tool handle that stage, so the stencil owns only the CPU reball step. When a phone stays dead after flash, a fresh reball rules out the CPU joints as the cause.
Why Technicians Choose Model-Specific Bumblebee Stencils
A model-matched template removes alignment guesswork. You stop reshaping a universal plate to fit, and you spend that time on pad cleaning and reflow control, where most reball failures start. The QS41 also pairs with the other Qianli Bumblebee numbers you may already hold, so the Note 4 plate slots into the same routine you use for newer Samsung boards. Stock it alongside a reballing kit, so tin, flux and fine tweezers sit next to the template. Check the plate against the chip before you commit heat, since fit is the one step you verify yourself. As your bench grows, the upgrade path runs from a basic hot air station and soldering iron to a stronger rework setup and a higher-magnification microscope, and the stencil stays the same.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Dedicated pattern for the Samsung Galaxy Note 4 (APQ8084)
- ✓Covers the CPU, BGA529 and eMCP footprint
- ✓Square holes with rounded angles for BGA work
- ✓Part of Qianli’s Bumblebee stencil range
- ✓Universal Series pattern naming for easy catalogue matching
- ✓Listed by the supplier as sturdy, precise and durable
- ✓Works with a hot air station, soldering station and reballing kit
- ✓Suits CPU-level repair on Note 4 dead phone and hang on logo boards
Specifications
| Brand | Qianli |
|---|---|
| Model | QS41 |
| Category | BGA Reballing Stencil (Bumblebee Series) |
| Compatibility | Samsung Galaxy Note 4, Qualcomm APQ8084 CPU / BGA529 / eMCP, Universal Series |
| Supported Devices | Samsung Galaxy Note 4 |
| Technology | Square-hole, round-angle BGA stencil |
Common Repair Uses
- ✓Real-world CPU-level reballing on Note 4 boards
- ✓CPU reballing after chip removal
- ✓Reballing a BGA529 package on an APQ8084 board
- ✓eMCP reballing
- ✓Repairing a Note 4 board that stays dead after a CPU hardware fault
- ✓Reballing a chip before refitting it after pad cleaning
- ✓Replacing a damaged CPU with a fresh reballed unit
- ✓Shop-level Note 4 board repair where a matched template saves alignment time
Compatible Devices
- ✓Verified scope is the Samsung Galaxy Note 4 and the Qualcomm APQ8084 platform
- ✓Samsung Galaxy Note 4
- ✓Qualcomm APQ8084 CPU
- ✓BGA529 package footprint
- ✓eMCP footprint
- ✓Qianli Universal Series pattern
- ✓Samsung SAM2 Note Series boards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which CPU and package types does the Qianli QS41 stencil cover?
What opening shape do Qianli Bumblebee stencils like the QS41 use?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock


