Relife RL-C210-I Straight Soldering Tip for 210 Handles
₨ 1
Relife RL-C210-I Straight Soldering Tip for Micro-Soldering
The Relife RL-C210-I is a replacement tip for 210 series soldering handles, built for work on crowded mobile and PCB boards. It uses a copper core with multilayer nano-galvanic plating, which supports fast heat transfer and consistent solder wetting. Its straight profile gives you direct access to tight pads, jumper points, and connector pins. Swapping the tip takes seconds on a plug-in handle, so you can change profiles during a repair without rebuilding your bench setup.
Out of stock
Relife RL-C210-I Soldering Tip Built for Precision Board Work
The Relife RL-C210-I is a straight replacement tip for the 210 series handle family. If your daily work includes flying jumper wires, pad restoration, and connector rework on mobile boards, this tip covers that workflow without forcing you to switch tip families. Its copper core and plating are designed for steady heat delivery, so you get a tip that recovers temperature quickly between joints. For repair benches working through a series of small solder points, that consistency keeps your joints clean and your rework time predictable.
Where the Straight Point Fits Your Repair Workflow
Your repair bench usually moves through a sequence: diagnosis, board inspection under magnification, then targeted soldering. The straight point suits the middle stage, where you need to reach a single pad or jumper point without disturbing surrounding components. When you lift a pad or reroute a trace, you need a clean approach angle and a tip that holds a precise contact area. This tip gives you that control, especially when you pair it with a microscope and a stable PCB holder.
Use it for flying jumper wire work on mobile motherboards, where you attach a fine wire to a test point and need a small, focused heat zone. It also handles connector pin rework, where pins sit close together and excess heat can lift neighboring pads. Keep your soldering station temperature at a level that melts solder quickly without overheating the trace. Once your joints look correct under the microscope, move to electrical testing with a multimeter before you return the board to service.
Copper Core, Plating, and Tinning Behavior
The tip’s performance depends on how it handles heat and solder. The copper core moves heat from the element to the working point, which helps the tip keep temperature during consecutive joints. The multilayer nano-galvanic plating supports solder adhesion and reduces oxidation between sessions. Together, these two features give you a tip that tins well and wets pads evenly, which matters most when you work on delicate copper traces.
Tin the tip before your first joint, and keep a thin layer of solder on the working surface during use. A clean, tinned tip transfers heat faster and reduces the risk of solder bridging. When you notice poor wetting or a dull surface, clean the tip on a damp sponge or brass wool, then retin it before continuing. Regular cleaning protects the plating and extends the useful life of the tip across many repair sessions.
Handle Fit and Replacement on the Bench
Relife designed the C210 series for plug-in replacement, so you change tips without tools or complex setup. Confirm that your handle belongs to the 210 series before you order, since fit depends on the handle family. Once the tip seats correctly, check that it sits firmly and does not wobble during light pressure.
Store spare tips in a dry, organized holder so you can switch between straight, curved, and knife profiles without searching through your kit. A bench with a few profiles on hand lets you match the tip to each board. Pair the RL-C210-I with a soldering station, a stable PCB holder, and a microscope to build a complete micro-soldering setup for mobile repair work across Pakistan.
| Weight | 0.10 kg |
|---|
Key Features
- ✓Straight fine-point profile for precise access to tight pads
- ✓Plug-in design for fast tip replacement on 210 series handles
- ✓Copper core supports consistent heat transfer
- ✓Multilayer nano-galvanic plating for solder adhesion
- ✓Plating resists oxidation during regular bench use
- ✓Fast temperature recovery between consecutive joints
- ✓Suited to flying jumper wire and pad restoration tasks
- ✓Works with a microscope-based micro-soldering setup
Specifications
| Brand | Relife |
|---|---|
| Model | RL-C210-I |
| Category | Soldering Tips |
| Compatibility | 210 series handles |
| Technology | Multilayer nano-galvanic plating |
| Material | Copper core |
Common Repair Uses
- ✓Micro-soldering and board-level rework on mobile phones and PCBs.
- ✓Flying jumper wire attachment on mobile motherboards
- ✓Pad restoration on lifted PCB pads
- ✓Connector pin rework on mobile boards
- ✓Micro-soldering of small SMD components
- ✓Joint repair at charging port and flex connector points
- ✓Re-tinning and rework of through-hole pins
- ✓Test point wire attachment during board diagnostics
- ✓Repair of cracked solder joints on board-to-flex connectors
Compatible Devices
- ✓Scope is handle-level and tool-level, not device-specific.
- ✓210 series plug-in soldering handles
- ✓Relife C210 series soldering stations
- ✓Mobile phone motherboards (universal, not device-specific)
- ✓PCB micro-soldering on general electronic boards
- ✓Flying jumper wire work on mobile boards (universal, not device-specific)
- ✓Pad repair on PCB traces
- ✓Connector pin soldering
- ✓Other 210 series handle models (confirm fit before ordering)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which handle does the RL-C210-I fit?
How does the nano-galvanic plating affect solder adhesion?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



