SM5451 Charging IC – 6A Switched-Capacitor Charger
₨ 350
SM5451 Charging IC for Mobile Repair
The SM5451 is a switched-capacitor charging IC from Silicon Mitus, rated for up to 6A in 2:1 forward mode and 5A in 1:1 forward mode. It also handles reverse IBUS current, with limits of 2.25A in 1:2 reverse and 4.5A in 1:1 reverse mode. For technicians, this makes it a board-level part for charging faults where the power path has failed, not just the USB port. Match the SM5451 marking on your donor board before ordering. Test with a current-limited bench supply after fitting, and confirm the battery takes charge before you reassemble the phone.
SM5451 Charging IC: Switched-Capacitor Charging for Your Repair Bench
The SM5451 charging IC is a switched-capacitor charger from Silicon Mitus, built to move high charging current into the battery. When a board carries this part, the IC sits between the input bus and the battery, so its condition controls how much current reaches the cell. Knowing its modes and limits helps you decide whether a no-charge complaint points to the IC, the input path, or the battery side. This guide covers the verified operating figures from the manufacturer’s datasheet, the reverse-current behaviour, and the checks you should run before any replacement.
Quadruple Mode Operation
The IC offers four operating modes. Two are forward modes for charging, 2:1 and 1:1, and two are reverse modes for IBUS current, 1:2 and 1:1. In 2:1 forward mode the IC delivers up to 6A into the battery, which is the headline figure for fast-charge work. In 1:1 forward mode the ceiling drops to 5A. The datasheet also lists 97 percent efficiency at VBAT 4.4V and 5A in 2:1 mode. High efficiency at high current means less heat lost in the IC, so keep those numbers in mind when you read a board’s temperature during a test run.
Reverse Mode and Power Path Checks
The reverse modes handle current flowing from the battery back toward the input bus, with IBUS limits of 2.25A in 1:2 reverse and 4.5A in 1:1 reverse. These figures matter when a phone powers up from the battery but refuses a wall adapter, or when the bus side reads dead on your meter. Check the input rail, the IC’s supply pins, and the battery connector voltage before you remove anything. A shorted or leaking IC often shows a warm spot and a bench-supply current draw above the expected idle level. Treat the part as a board-level replacement only after simpler faults are cleared.
Practical Replacement Workflow
Confirm the SM5451 marking on the donor board before you order, because Samsung boards can use different charging ICs in similar package styles. Remove the IC with hot air at a controlled temperature, clean the pads, and inspect for lifted copper. Fit the new part, then test charging with a current-limited bench supply, starting at a low limit and watching for voltage drop across the path. A good result shows the battery taking charge at the expected rate while the board stays cool under load. Record the board revision and the test result on the job card, so the next technician knows exactly what you fitted.
| Weight | 0.1 kg |
|---|
Key Features
- ✓6A maximum charging current in 2:1 forward mode
- ✓5A maximum charging current in 1:1 forward mode
- ✓2.25A IBUS current in 1:2 reverse mode
- ✓4.5A IBUS current in 1:1 reverse mode
- ✓97% efficiency at VBAT 4.4V and IBAT 5A in 2:1 mode
- ✓Switched-capacitor architecture with quadruple operating mode
- ✓Embedded infinite regulation loop with an internal QRB switch
Specifications
| Brand | Silicon Mitus |
|---|---|
| Model | SM5451 |
| Category | Charging IC |
| Technology | Switched-capacitor charger, quadruple mode |
| Charging Current | 6A maximum (2:1 forward mode), 5A maximum (1:1 forward mode) |
| IBUS Current | 2.25A maximum (1:2 reverse mode), 4.5A maximum (1:1 reverse mode) |
| Efficiency | 97% at VBAT 4.4V, IBAT 5A (2:1 mode) |
Common Repair Uses
- ✓Diagnosing and replacing the charging IC on mainboards where the charging path has failed.
- ✓Restoring charging on a dead phone after confirming a charging-path fault on the board
- ✓Replacing the IC after a short on the input rail
- ✓Diagnosing no-charge complaints where the USB port tests fine
- ✓Diagnosing phones that run from the battery but refuse adapter input
- ✓Checking reverse-current behaviour when the bus side reads dead
- ✓Verifying IC health with a current-limited bench supply before refitting
Compatible Devices
- ✓oard-level match only, based on the SM5451 marking on the donor mainboard.
- ✓Samsung mainboards bearing an SM5451 IC marking (match the marking before ordering)
- ✓Replacement for the same marked IC position on the board, not a universal fit



