MECHANIC MCN-N6 Soldering Iron Tip Refresher Paste 35g
₨ 1
Restore Oxidized Soldering Iron Tips Fast
The MECHANIC MCN-N6 soldering iron tip refresher paste removes oxidized, blackened layers from iron tips and re-tins the surface so solder flows again. It suits mobile phone technicians, PCB rework specialists, and service centers that need consistent tip performance during BGA reballing, IC removal, and motherboard repair. Apply it to a heated tip, wipe off the residue, and the tip returns to a working state within one or two passes. The 35g tin fits easily on any repair bench and lasts through many cleaning cycles. Use it on the tip itself and keep your flux for the joints.
Out of stock
Soldering Iron Tip Refresher Paste for Oxidized Tips
A soldering iron tip that turns black and stops accepting solder is one of the most common problems on a repair bench, and a soldering iron tip refresher paste solves it directly. The MECHANIC MCN-N6 is a 35g tin of cleaning compound designed to remove the oxide layer from the metal tip and re-tin the surface beneath it. Sponges and brass wire cleaners wipe away visible dirt, but they usually leave the oxidized layer in place, so the tip keeps losing heat transfer. This paste works on the tip itself, not on the joint, which means it complements your flux and solder wire rather than replacing them. Your repair work depends on a tip that carries heat evenly into small pads, so restoring tip condition protects the quality of every joint you make. The sections below explain where the paste fits in your workflow, how to apply it correctly, and how to store it so it stays effective.
Where It Fits in Your Soldering Workflow
A dull, de-wetted tip transfers heat unevenly, and uneven heat raises the risk of lifted pads, cold joints, and overheating on sensitive phone components nearby. Many board comebacks trace back to a poor joint that started with a tip losing its tinning during the job. You get the most from this paste when you use it mid-job, the moment a tip stops accepting solder, rather than pushing a degraded iron through a reballing session or an IC change. During BGA reballing, a properly tinned tip helps you seat small balls cleanly and keep pad temperatures under control. On motherboard-level work, the same tip often handles fine-pitch pins, so consistent tinning directly affects your accuracy. Keep the tin next to your flux paste, solder wire, and hot air station, since all of these tools depend on consistent heat transfer to perform.
Applying the Paste to Your Iron Tip
Heat your iron to its normal working temperature before you start, because a cold tip will not release the oxide layer properly. Press or rotate the hot tip gently into the paste, then move it across the compound surface for a few seconds until the oxide begins to lift. Wipe the tip with a dry cloth or a standard sponge to remove the residue, and check whether bright metal shows across the working face. A tip that looks dark but still has some clean metal usually returns to a tinned state after one application. A heavily oxidized tip may need a second pass, so repeat the process after wiping the tip clean. Stop once the tip accepts solder evenly across its face, since over-treating a tip wastes compound without improving the result.
Storage and Handling Habits
Close the tin tightly after every session so the compound stays workable and does not dry out at the edges. Keep dust, solder splatter, and other debris out of the paste, because contamination can affect how cleanly it re-tins a tip. Store the tin in a dry place away from heat sources and clear of solder residue on the bench. A busy service center can keep one tin at each station, which helps every iron maintain consistent performance across a full shift. Good storage also keeps your tip replacement costs low over the life of your irons. Treat the paste as a periodic maintenance item rather than a daily consumable, and replace the tin only when it stops restoring tips.
| Weight | 0.9 kg |
|---|
Key Features
- ✓Restores oxidized soldering iron tips to a tinned, working surface
- ✓Removes black oxide buildup without relying on sponge wiping alone
- ✓Works on all standard soldering iron tip types
- ✓Lead-free formula
- ✓Fast application, typically within one or two passes
- ✓Compact 35g tin for repair benches
- ✓Helps extend tip life and reduce replacement purchases
- ✓Supports consistent heat transfer for cleaner joints
Specifications
| Brand | MECHANIC |
|---|---|
| Model | MCN-N6 |
| Category | Soldering Accessories |
| Compatibility | Universal soldering iron tips |
| Technology | Tip re-tinning compound |
| Weight | 35g |
Common Repair Uses
- ✓Tip restoration and maintenance during phone and PCB repair workflows.
- ✓Restoring blackened, de-wetted soldering iron tips
- ✓Preparing tips before BGA reballing sessions
- ✓Maintaining tips during motherboard-level IC removal and reinstallation
- ✓Keeping fine-pitch tips tinned for SMD component work
- ✓Restoring tip performance mid-job during phone board rework
- ✓Routine tip upkeep at mobile repair benches
- ✓Maintaining PCB rework station tips in service centers
- ✓Tip maintenance during soldering practice at training institutes
Compatible Devices
- ✓Universal, not device-specific. Covers standard soldering iron tips regardless of iron brand.
- ✓Chisel tips used on general soldering irons
- ✓Conical and pointed tips for fine SMD work
- ✓Knife-edge tips for drag soldering
- ✓Bevel and flat tips used in IC and board repair
- ✓Tips used on standard soldering handpieces
- ✓Tips used on rework stations with a standard soldering iron handle
- ✓Tips used on desoldering tools
- ✓Not for hot air rework nozzles, which need a cleaning method suited to nozzles
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can this paste restore a badly oxidized soldering iron tip?
Can I use this paste on hot air rework nozzles?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



