Mechanic V5B45 Low Temp Solder Paste 138°C 42g
₨ 1
V5B45 Low Temperature Solder Paste for BGA and SMD Work
The Mechanic V5B45 low temperature solder paste melts at 138°C, so you can reflow BGA and SMD joints without pushing heat into nearby ICs and plastic parts. The alloy is Sn42Bi58, a tin and bismuth mix that reflows at a much lower point than standard solder paste. Each 42g pack gives your repair bench enough material for several reballing and component jobs. Use it for controlled reflow on motherboards, laptop boards, and other heat-sensitive circuit boards, and pair it with a stencil or a fine application tool for clean, even deposits.
Out of stock
V5B45 Low Temperature Solder Paste for Controlled BGA Reflow
A V5B45 low temperature solder paste gives you control over the heat that reaches a board. This paste melts at 138°C, which sits far below the 220°C range where standard solder pastes flow. For a technician working on phones, laptops, and tablets, that gap matters. Heat-sensitive ICs, plastic connectors, and flexible sections tolerate less thermal stress than the main board, so a lower melting point reduces the risk of damage during reflow. The V5B45 fits workflows built around BGA reballing, component replacement, and pad repair on compact, densely packed boards.
Alloy Composition and Melting Behavior
The V5B45 uses an Sn42Bi58 alloy, with about 42 percent tin and 58 percent bismuth. That ratio sets the melting point at 138°C. Bismuth-rich alloys flow at lower temperatures, so you complete reflow before heat spreads across the entire board. Once the joint cools, it forms a stable mechanical and electrical bond. Keep one trade-off in mind. Sn42Bi58 joints are more brittle than tin-rich joints under sustained bending or impact, so avoid placing a repaired board where flex or frequent knocks will stress the solder. The paste has a smooth, bubble-free consistency that helps you deposit clean, even volumes on each pad, which reduces bridging and cold joints on fine-pitch work.
Application Workflow on BGA and SMD Parts
Start every job with clean pads. Remove old solder with a wick, then clean the flux residue so the new paste bonds to bare copper. Apply the V5B45 through a stencil for BGA reballing, or with a fine tool for SMD pads, and keep the deposit even across each pad row. Place the component carefully and reflow with your hot air station, moving the nozzle in steady passes so heat reaches every joint evenly. Watch the paste as it melts. Once the joints look bright and settle into place, stop applying heat and let the board cool naturally. Avoid forcing the cooldown with strong air, since rapid temperature shifts can crack fresh joints. Keep airflow gentle so nearby small components do not shift before the alloy sets. After the board cools, check continuity with a multimeter, and inspect the joints under a microscope if your bench has one.
Storage, Handling and Safety
Store the container tightly closed in a cool place, and keep it away from food, drink, and animal feed. The product information warns that inhalation and ingestion are harmful, and that repeated skin contact causes problems, so work in a ventilated area and wash your hands after each session. Avoid eating, drinking, or smoking while you handle the paste. Transfer a small amount to your work tray rather than opening the full pack for every job, which limits exposure and keeps the rest of the paste clean. If paste is swallowed, seek medical attention immediately. These habits protect you on a busy repair bench, where paste tends to end up on tools, gloves, and nearby boards.
| Weight | 0.4 kg |
|---|
Key Features
- ✓138°C melting point
- ✓Sn42Bi58 alloy
- ✓42g package
- ✓Smooth, bubble-free consistency
- ✓Strong tin bonding with good conductivity
- ✓Large solder load for clean pad coverage
- ✓Suited to BGA and SMD work
- ✓Suited to stencil and manual application
Specifications
| Brand | Mechanic |
|---|---|
| Model | V5B45 |
| Category | Solder Paste |
| Compatibility | Universal, not device-specific |
| Technology | Low temperature solder paste, 138°C melting point |
| Material | Sn42Bi58 solder alloy with flux |
| Weight | 42g |
Common Repair Uses
- ✓BGA IC reballing with a stencil
- ✓Replacing SMD components on phone boards
- ✓Reflowing heat-sensitive ICs at a lower temperature
- ✓Pad repair and tin re-application on motherboards
- ✓Laptop board component replacement
- ✓Re-attaching BGA chips after board repair
Compatible Devices
- ✓Mobile phone motherboards for BGA and SMD reflow
- ✓Laptop motherboards and related circuit boards
- ✓Tablet and other compact SMD/BGA boards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What is the melting point of V5B45 solder paste?
Is V5B45 suitable for BGA reballing?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



