YCS 8.5W-50g Thermal Paste CPU Cooling Paste Silicone
₨ 1,650
YCS 8.5W Thermal Paste 50g for Repair Benches
The YCS 8.5W-50g Thermal Paste CPU Cooling Paste Silicone gives your workshop a 50g supply of 8.5W-rated silicone thermal grease. It fills the microscopic gaps between a heat-producing chip and its heatsink or shield, so heat leaves the processor faster. Technicians use it on phone boards, laptop motherboards, notebooks and desktop CPUs that run hot, restart on their own or throttle under load. The 50g pack suits shops that service several devices a day, because one pack covers many applications. Mechanicpk supplies it to repair shops and service centers across Pakistan.
In stock
YCS 8.5W Thermal Paste 50g for Mobile, Laptop and CPU Cooling Repair
The YCS 8.5W thermal paste 50g pack gives a repair bench a large, practical supply of silicone-based thermal grease rated at 8.5W. Every processor, GPU and power chip on a board loses heat through a thin contact layer. When the old compound dries out or cracks, that layer stops carrying heat away, and the device overheats, restarts or slows down. You replace the failed layer with fresh paste, and the chip gets a working heat path again. The YCS 8.5W-50g Thermal Paste CPU Cooling Paste Silicone belongs in the consumables drawer next to your flux and solder, because almost every reassembly after a hardware fault, reballing job or CPU cleaning ends with a thermal paste step.
Where Thermal Paste Fits in a Repair Workflow
Thermal paste works at the end of the repair process, after the board work is finished and tested. You remove the old compound, clean the chip surface and the heatsink or shield contact area, and apply a fresh thin layer before you close the device. This applies in several repair scenarios. A laptop that shuts down under load needs new paste on the CPU and GPU. A phone that overheats after a long repair session needs its shield and chip contact area re-pasted. A desktop CPU that throttles needs the cooler lifted and the compound renewed. The paste does not fix a failed IC or a damaged track, so test the board first and treat the paste as the last step that protects your finished work.
Why the 8.5W Grade and the 50g Pack Suit a Busy Workshop
The product page for this YCS series lists 4W, 6W and 8.5W grades. The 8.5W grade is the highest of the three, and it moves heat across the contact layer faster than the lower grades. That matters on compact boards where heat has little room to spread. The 50g content size matters just as much for a shop with steady footfall. Small 1g and 4g syringes run out within a few jobs, while a 50g pack covers hundreds of thin applications. Your cost per repair drops, and you stop pausing mid-job to look for more paste. The silicone base spreads smoothly, so a small amount covers a chip surface without thick, messy layers.
Application Notes for Technicians
Clean the chip and the cooling surface first with a suitable cleaning fluid and a lint-free cloth, because old paste and flux residue block heat transfer. Apply a small amount in the centre of the chip, then press the heatsink or shield down evenly and let the pressure spread the paste. A thin, even layer works better than a thick one, since extra paste insulates instead of conducting. Keep paste away from connectors, pads and any area you have not cleaned, and wipe off overflow before you power the board. After assembly, run the device under load for a few minutes and watch the temperature and stability. A good microscope helps you inspect the chip surface before you apply paste, and a PCB holder keeps the board steady during cleaning.
Related Tools for the Same Workflow
Thermal paste pairs naturally with the tools you already use for board work. Hot air stations and soldering stations handle the rework that comes before re-pasting, reballing kits prepare BGA chips that you then cool with fresh compound, and a multimeter confirms that the board is healthy before you seal the device. Browse these categories at Mechanicpk to complete your bench around this thermal paste.
| Weight | 0.50 kg |
|---|
Key Features
- ✓50g bulk pack for high-volume repair shops
- ✓8.5W-rated thermal conductivity
- ✓Silicone-based paste that spreads easily
- ✓Fills small gaps between chip and heatsink
- ✓Helps reduce heat on CPUs, GPUs and motherboards
- ✓Suits phones, laptops, notebooks and desktop PCs
- ✓Compact pack at 123 x 39.5 x 40 mm
- ✓Part of the YCS 4W, 6W and 8.5W thermal paste series
Specifications
| Brand | YCS |
|---|---|
| Model | 8.5W-50g |
| Category | Thermal Paste |
| Technology | Silicone-based thermal grease |
| Content | 50g |
| Thermal Conductivity | 8.5W |
| Dimensions | 123 x 39.5 x 40 mm |
| Weight | 80g (gross) |
Common Repair Uses
- ✓Re-applying thermal compound during phone, laptop and desktop servicing.
- ✓Replacing dried thermal paste on laptop CPUs
- ✓Re-pasting laptop GPUs after cleaning
- ✓Cooling-layer renewal after reballing or IC replacement
- ✓Fixing overheating after a long repair session
- ✓Reducing heat-related restarts on notebooks
- ✓Re-pasting desktop CPUs after cooler removal
- ✓Servicing graphics cards that run hot
- ✓Restoring the heat path on phone boards with shields
Compatible Devices
- ✓Universal thermal interface compound for mobile phones, laptops, notebooks and desktop CPU/GPU cooling. It is not device-specific.
- ✓Mobile phone motherboards
- ✓Laptop CPUs
- ✓Laptop GPUs
- ✓Notebook motherboards
- ✓Desktop CPU coolers
- ✓Graphics cards
- ✓Heatsink-to-chip contact surfaces
- ✓Shield-to-chip contact surfaces on repaired boards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What do the 8.5W and 50g in the name mean?
Can this thermal paste help with overheating and frequent restarts?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



