BQ25975 Switched Cap Fast Charger IC for Mobile Repair
₨ 500
TI BQ25975 Charging IC for Fast-Charge Board Repair
The BQ25975 charging IC powers the high-current stage of a smartphone fast-charging system. It converts adapter power through a switched-capacitor network instead of an inductor, which lets the battery take a high charge current while the cable carries far less. A main buck charger on the same board runs the rest of the cycle, and the phone’s host processor manages the IC over I2C. When a phone charges normally but refuses to fast charge, technicians often trace the fault to this stage. You get a precise replacement part for clean IC change work on Android charging sections.
BQ25975 Switched Cap Charger IC for High-Current Smartphone Charging
The BQ25975 switched cap charger IC sits in the high-current branch of a smartphone charging circuit. It transfers energy from the USB input to a single-cell battery through flying capacitors rather than a coil. Texas Instruments switched-cap chargers work on a 2:1 ratio: the stage halves the input voltage and doubles the current it hands to the battery. That ratio keeps current through the cable and USB port low while the battery still receives aggressive fast-charge current. Less current in the cable means less heat in the charging port, the flex, and the connector, which are the parts that fail most often on fast-charging phones. For your repair bench, this IC is a targeted replacement for one specific fault area, the fast-charge path.
How the Switched-Cap Stage Shares Work with the Main Charger
The BQ25975 never runs a complete charging cycle by itself. A standard buck charger on the same board handles pre-charge, constant-voltage finishing, and termination. The switched-cap stage takes over the high-current window once the adapter and phone agree on a fast-charge voltage. The host processor communicates with the IC over I2C, enables the stage, and sets its protection limits. This split explains a symptom you see constantly in Pakistani repair shops. The phone still charges on a normal adapter, but fast charging never starts, and the phone stays cool during charging. The main charger keeps the slow path working, so a failed switched-cap IC almost never presents as a dead phone.
Protection, Monitoring, and Why a Jumper Will Not Help
Switched-cap chargers in this class combine input overvoltage protection, IC thermal regulation, and battery temperature monitoring with an integrated ADC. That ADC reports live voltage and current readings to the host. Phone software watches those readings throughout every fast-charge session and shuts the high-current path the moment anything looks abnormal. Jumper lagana across a damaged or missing IC therefore gains nothing. The host loses its I2C partner, and fast charging stays locked out. The flying capacitors around the BQ25975 deserve equal attention. A cracked or shorted capacitor reproduces the exact symptoms of a failed IC, so test the capacitor network before you commit to a replacement. Replacement remains the only reliable fix for a genuine hardware fault in this stage.
Diagnosing and Replacing the BQ25975 on Your Repair Bench
Start with a USB current meter and a known-good fast charger. If the phone sits at standard charging current with no heat around the charging section, suspect the switched-cap stage first. Measure the IC’s input and output rails to ground in diode mode with a multimeter, and compare the readings against a healthy board of the same model. Liquid damage and low-quality adapters with unstable output cause most failures in this area. For the IC change, work with a temperature-controlled hot air station, good flux, a PCB holder, and a stereo microscope, because tiny passives surround the BQ25975 and shift under careless airflow. After seating the new switched capacitor fast charger IC, clean the flux, inspect every joint under magnification, and confirm fast-charge current on the meter before closing the phone. A DC power supply with current readout speeds up short detection on future charging jobs. A higher-magnification microscope makes a natural upgrade if you handle many board-level charging repairs.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Switched-capacitor conversion with no inductor in the fast-charge path
- ✓2:1 operation that delivers high battery current from lower cable current
- ✓Works in parallel with a main buck charger on the same board
- ✓I2C interface for host-controlled enable and protection settings
- ✓Integrated ADC for live voltage and current reporting
- ✓Input overvoltage protection on the fast-charge path
- ✓IC thermal regulation and battery temperature monitoring
- ✓Lower heat in the USB port, cable, and connector during fast charging
Specifications
| Brand | Texas Instruments |
|---|---|
| Model | BQ25975 |
| Category | Mobile Phone Charging IC |
| Compatibility | Single-cell Li-ion/Li-polymer smartphone fast-charging circuits with a switched-cap stage |
| Supported Devices | Android smartphones using parallel switched-cap fast charging |
| Technology | Switched-capacitor (charge pump) fast charging, I2C controlled |
Common Repair Uses
- ✓Fast charging not working while normal charging still works
- ✓IC change after liquid damage on the charging section
- ✓Short-circuit isolation on the charging IC’s input or output rails
- ✓Replacement after failure caused by a faulty or unstable adapter
- ✓Low charging current diagnosis with a USB meter
- ✓Rework of the IC and flying capacitors on charging boards
- ✓Fast-charge hardware fault confirmation before board replacement
Compatible Devices
- ✓Verified at architecture level, not model-specific. Match the marking on the original IC before replacement.
- ✓Single-cell Li-ion and Li-polymer smartphones
- ✓Android phones with high-current wired fast charging
- ✓Charging boards that pair a switched-cap stage with a main buck charger
- ✓Boards with a flying capacitor network around the charging IC
- ✓Phones whose fast-charge path is managed by the host processor over I2C
- ✓Tablets using single-cell switched-cap charging designs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can I bypass the BQ25975 with a jumper if fast charging stops?
How do I check if the BQ25975 is shorted on the board?
Related products
339S00108 WiFi IC For iPad Air iPad Pro 9.7 Replacement
In stock
339S0223 For iPad 5/Air1 A1474 Wifi IC – U5800 WiFi Module
In stock
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock
PM8916 Power Control IC – Qualcomm PMIC for MSM8916 Boards
In stock



