Skyworks SKY77365-11 PA IC Quad-Band GSM Power Amplifier

₨ 300

77365-11 PA IC for 2G Network Repair

The 77365-11 PA IC is Skyworks’ SKY77365-11, a quad-band power amplifier module that drives transmit power on GSM850, GSM900, DCS1800 and PCS1900. It carries GMSK voice and data at fixed gain, handles EDGE linear modulation, and supports Class 12 GPRS multi-slot operation. One InGaP die holds two HBT amplifier blocks. A CMOS controller sets bias and reports a product ID over the RFFE MIPI bus. The package measures 3.0 x 3.5 x 0.8 mm. You get a complete transmit stage in one part when a handset shows a network issue, a heavy current draw, or a shorted PA rail.

17 People watching this product now!
Description

77365-11 PA IC: Skyworks Quad-Band GSM Power Amplifier Module

The 77365-11 PA IC is Skyworks’ SKY77365-11 power amplifier module. It drives transmit power on the 2G side of a handset. When a phone shows a network issue, drops calls right after it registers, or pulls heavy current at power-on, the PA stage belongs near the top of your suspect list. This module puts two InGaP HBT amplifier blocks, 50-ohm input and output matching, and a CMOS control die on one laminate substrate. That means a single reflow replaces the entire transmit stage. Mechanicpk stocks the exact marking for technicians who handle board-level network faults and need the correct part, not a lookalike.

Inside the SKY77365-11 Power Amplifier Module

Skyworks splits the transmit work between two amplifier blocks on one InGaP die. One block covers GSM850 and GSM900. The other covers DCS1800 and PCS1900. Both blocks draw from two shared supply pads, which matters during diagnosis: a failure in either block can load the same rail. The module amplifies GMSK signals at fixed gain, handles EDGE linear modulation, and supports Class 12 GPRS multi-slot operation.

A custom CMOS multi-function controller (MFC) sets PA bias and reports a product ID back to the baseband over the RF Front-End MIPI (RFFE) bus. Because of that read-back, the phone’s software expects this exact part. The baseband programs bias through MIPI registers, not through analog control pins. A substitute with a different controller will not respond the same way, even if it fits the footprint.

Diagnosing a 77365-11 PA IC Fault on Your Bench

Start with current. Feed the board from a DC power supply and watch the draw at power-on. If the reading jumps high and the phone never boots, measure the PA supply line to ground on your multimeter. A near-zero reading points to the PA or to a capacitor on the same rail. Lift the suspect capacitors first, since they take less time.

If the short stays after the capacitors come off, the PA is the likely source, and IC change karna becomes the fix. A thermal camera or a thin coat of rosin quickly shows which component heats up under injected voltage.

For no-service faults with normal current, check the antenna path and the RF switch before you touch the PA. Then inspect the module under your microscope for cracked joints, lifted pads, or green corrosion along its edges. That last check matters most on liquid-damaged boards.

Replacing the Quad-Band GSM PA IC Cleanly

The module’s plastic overmold and laminate base make it behave like any small PA during rework. Remove the RF shield if the board has one. Clamp the board in a PCB holder, apply flux, and preheat evenly. Lift the old part with your hot air station at moderate airflow so nearby passives stay in place.

Clean the pads with wick and your soldering station, then tin them flat so the new module seats level. Align the replacement 77365-11 PA IC by its pin-1 marker, reflow, and let it cool naturally before testing. Check current draw again first, then confirm network registration and place a test call on a 2G network.

If you still rework PAs by eye, a stereo microscope is the upgrade that pays off fastest. Pad damage on modules this size stays invisible until it causes a second failure.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Quad-band coverage: GSM850, GSM900, DCS1800, PCS1900
  • Two InGaP HBT amplifier blocks on a single die
  • Fixed-gain GMSK and fixed-gain linear EDGE modulation
  • Class 12 GPRS multi-slot operation
  • CMOS multi-function controller for bias and product ID read-back
  • Fully programmable over the RFFE MIPI interface
  • Internal 50-ohm input and output matching
  • Compact 3.0 x 3.5 x 0.8 mm overmolded module

Specifications

BrandSkyworks Solutions
ModelSKY77365-11
CategoryPower Amplifier Module (PA IC)
CompatibilityGSM850 / GSM900 / DCS1800 / PCS1900, GMSK and EDGE modulation, Class 12 GPRS
Supported Devices2G quad-band cellular handsets
TechnologyInGaP HBT amplifier die with CMOS multi-function controller, RFFE MIPI control, 50-ohm matched input/output
MaterialMulti-layer laminate substrate with plastic overmold
Dimensions3.0 mm x 3.5 mm x 0.8 mm

Common Repair Uses

  • Replacing a shorted PA that loads the supply rail and causes a dead phone
  • Fixing heavy current draw at power-on traced to the PA stage
  • Restoring 2G network signal after a “no service” fault
  • Repairing call drops that happen during transmit
  • Replacing a PA damaged by liquid or corrosion
  • Swapping a PA with cracked joints after a drop
  • Fixing PA overheating during calls
  • Rebuilding the transmit stage after RF section board damage

Compatible Devices

  • Verified at band and interface level. Skyworks does not publish a device model list, so match the marking on the original IC before you replace it.
  • 2G quad-band GSM/GPRS/EDGE cellular handsets
  • Handset boards fitted with the original SKY77365-11 marking
  • GSM850 band transmit path
  • GSM900 band transmit path
  • DCS1800 band transmit path
  • PCS1900 band transmit path
  • Boards using RFFE MIPI front-end control
  • Class 12 GPRS multi-slot capable radios

FAQ

What is the product name?
The product name is Skyworks SKY77365-11 PA IC.
What is the brand of this product?
The brand of this product is Skyworks Solutions.
What is the model of this product?
The model of this product is SKY77365-11.
What is this product used for?
This product is used for replacing the quad-band GSM power amplifier in mobile phones with network, transmit, or PA short faults.
Which devices are compatible with this product?
This product is compatible with 2G quad-band GSM/GPRS/EDGE handsets that use the SKY77365-11 module, covering GSM850, GSM900, DCS1800 and PCS1900.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can a shorted 77365-11 PA IC make a phone dead?
Yes. Both amplifier blocks share common supply pads, so an internal short can pull the PA supply rail down, causing heavy current draw and no boot. Rule out the capacitors on that rail before you replace the PA.
Can I replace the 77365-11 with a different PA IC number?
Use the same marking. The SKY77365-11 reports its product ID and takes bias settings over RFFE MIPI in a 3.0 x 3.5 mm footprint, so a part with a different footprint or controller will not work as a direct replacement.