MAX20328B USB Type-C Audio Switch IC
₨ 450
MAX20328B USB Type-C Audio Switch IC for Board Repair
The MAX20328B is a USB Type-C audio and data switch IC from Analog Devices. It routes the DP/DM and SBU lines between USB 2.0 data and analog audio, and it protects those channels from overvoltage. It operates from 2.7V to 5.5V across a -40°C to 85°C range and comes in a 25-pin WLP package. For technicians working on USB-C audio faults or port-level damage, it is a fine-pitch board-level component that rewards careful reflow work.
MAX20328B USB Type-C Audio Switch IC Overview
The MAX20328B USB Type-C audio switch IC sits between the USB-C connector and the device’s data and audio paths. Its job is to route signals based on what is plugged in. When a USB 2.0 data signal is present, the chip passes data. When an audio accessory connects, it switches the same pins to analog audio. The MAX20328B also protects those channels from overvoltage. Manufacturer data places this part in smartphones, phablets, and tablet PCs, where one Type-C connector carries both signal types. Understanding this role helps you narrow a fault before you replace any part.
Where the MAX20328B Sits in the USB-C Port
On a Type-C port, the data and sideband (SBU) lines serve several functions. Without a switch, a USB 2.0 data signal and an analog audio signal would collide on the same pins. The MAX20328B selects the correct path for each case. Start your workflow at the connector. Check whether the port charges, whether the device enumerates as a USB device, and whether audio reproduces when an accessory goes in. If the fault follows the signal path through the switch, this IC becomes a candidate. Connector damage, cracked joints, and upstream power faults produce similar symptoms, so measure before you change anything. A clear fault map keeps your bench productive.
Audio Accessory Detection and Switching
When a USB-C audio accessory connects, the chip does more than route a signal. Its automatic impedance detection checks the audio configuration and sets the switch to match. The MAX20328B supports ±5V audio signals, which gives headroom above a standard audio swing. It also disables microphone bias when it detects a CC-pin connection event, which suppresses the pop noise users hear during insertion. If you test an accessory and hear a click or lose the microphone, inspect the CC lines and the connector before you blame the switch. Those lines drive the detection event the chip responds to, so a fault there can mimic a dead IC.
Overvoltage and Surge Protection on Type-C Lines
USB Power Delivery can place high voltage on the connector. A short or a cable fault can send that voltage into data and SBU lines that were never designed for it. The MAX20328B provides overvoltage-protected data and audio channels, and its USB Type-C contacts are rated as high ESD and surge-protected. Check the manufacturer datasheet for exact ratings before you rely on a figure in the field. When a port fails after a bad cable or an unstable power event, inspect the neighbouring components and the power path too. Replacing the switch alone will not fix a fault further upstream.
Power Profile, Package, and Handling
The MAX20328B operates from a 2.7V to 5.5V supply. Its typical input supply current is 256µA at 3.7V and 25°C, and its typical shutdown current is 3.9µA, which keeps standby drain low when the switch is disabled. The operating range is -40°C to 85°C. The part comes in a 25-pin WLP package and carries MSL 1, so it does not need moisture baking before reflow. Because the package is a fine-pitch wafer-level array, board-level replacement demands accurate reballing, controlled hot air, and precise alignment. Verify pin 1 orientation and the reflow profile before you power up the board.
| Weight | 0.1 kg |
|---|
Key Features
- ✓USB 2.0 data and audio switch paths with Beyond-the-Rails signal capability
- ✓Automatic impedance detection in audio configurations
- ✓Overvoltage-protected data and audio channels
- ✓Supports ±5V audio signals
- ✓High ESD and surge-protected USB Type-C contacts
- ✓Disables microphone bias on a CC-pin connection event to reduce pop noise
- ✓2.7V to 5.5V supply range
- ✓256µA typical supply current and 3.9µA typical shutdown current
Specifications
| Brand | Analog Devices |
|---|---|
| Model | MAX20328BEWA+T |
| Category | USB Type-C audio switch IC |
| Supported Devices | Smartphones, phablets, tablet PCs |
| Technology | USB 2.0 data and analog audio switching with overvoltage protection |
| Input Voltage | 2.7V to 5.5V |
Common Repair Uses
- ✓Diagnosing USB-C audio accessory faults such as no sound or a dead microphone
- ✓Checking USB-C port faults after an overvoltage event
- ✓Board-level reballing and replacement of the Type-C audio switch IC
- ✓Isolating faults between the connector, the switch, and downstream circuits
- ✓Investigating pop noise during accessory insertion
- ✓Verifying signal path continuity on USB 2.0 data lines
Compatible Devices
- ✓Verified scope is application-level, not device-specific.
- ✓USB Type-C smartphones (application scope per manufacturer)
- ✓Phablets (application scope per manufacturer)
- ✓Tablet PCs (application scope per manufacturer)
- ✓USB Type-C audio accessory ports
- ✓USB 2.0 data lines on Type-C connectors
- ✓Board-level replacement, not device-specific
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What is the operating voltage range of the MAX20328B?
Does the MAX20328B protect USB-C data lines from overvoltage?
Related products
339S0223 For iPad 5/Air1 A1474 Wifi IC – U5800 WiFi Module
In stock



