SGM41513 Charging IC – 3A Single-Cell Battery Charger
₨ 550
SGM41513 Charging IC for Li-Ion and Li-Polymer Battery Repair
The SGM41513 is a 3A single-cell battery charger with NVDC power path management and I2C control. It accepts a 3.9 V to 13.5 V input and charges through a 1.5 MHz synchronous buck stage, with OTG boost output up to 1.2 A. On your repair bench, it covers charging failures, dead-phone power path checks, and board-level IC replacement. The package is TQFN-4×4-24L, and every specification below comes from the manufacturer’s published data.
SGM41513 Charging IC: Power Path Control for Repair Benches
The SGM41513 charging IC sits between the input connector and the battery, so a fault here shows up as no charging, slow charging, or a phone that stays dead after a deep discharge. You test VBUS, check the power path, and then decide between a board-level repair and an IC change. Because the device is I2C programmable, its behavior depends on the register setup of the host board, so measure before you replace anything. This part targets smartphones, tablets, and portable systems that use single-cell Li-Ion or Li-polymer batteries. The sections below cover the input range, battery path behavior, and OTG protection features that matter during diagnosis.
3A Single-Cell Battery Charger Input Range
The SGM41513 accepts an operating input voltage from 3.9 V to 13.5 V and withstands up to 22 V sustained. That margin protects the charging stage when an adapter spikes or a 9 V or 12 V fast charging source feeds the board. The charger runs a 1.5 MHz synchronous buck topology, and it reaches 93.8 percent charge efficiency at 1.02 A from a 5 V input. At 2 A from a 9 V input, efficiency measures 89.8 percent, so the part stays efficient under fast charging loads. Input current limit (IINDPM) and VINDPM tracking adjust the source draw, which keeps a weak USB host from collapsing during charging. When you measure VBUS during fault diagnosis, compare the reading against this window before you blame the charger IC.
Battery Path, Instant-On and Ship Mode Behavior
The battery switch uses a 26 mΩ path, which keeps discharge losses low when the phone runs heavy loads from the battery. Instant-on operation lets the system start with no battery or a highly depleted one, so a dead phone can begin charging without waiting for a long pre-charge sequence. Ship mode holds battery leakage at about 2.5 µA, which means a board stored for weeks keeps its charge. Wake-up and full system reset control from the battery FET helps recover a host that locks up after a power event. Battery temperature sensing covers both charge and boost modes, so a faulty NTC circuit stops charging instead of pushing unsafe current into the cell.
I2C Controlled OTG Boost, Protection and Package
In OTG mode, the boost converter delivers up to 1.2 A and reaches 93.5 percent efficiency at 0.5 A and 92.2 percent at 1 A. Hiccup mode overcurrent protection and output short-circuit protection restart the converter automatically, so a shorted reverse-charge port does not burn the power stage. Selectable PFM mode improves light-load efficiency in both buck and boost operation, which helps standby current on the board. The part comes in a TQFN-4×4-24L package, so you need a matching 4×4 footprint and careful reflow when you replace it. Two related variants, SGM41513A and SGM41513D, exist, so check the IC revision marking on the board before you order a replacement. SGMICRO also offers the EVKIT-SGM41513 evaluation kit on request for bench validation.
| Weight | 0.1 kg |
|---|
Key Features
- ✓3.9 V to 13.5 V operating input range with up to 22 V sustained voltage
- ✓3A single-cell charging with 1.5 MHz synchronous buck topology
- ✓NVDC power path management with instant-on operation
- ✓I2C programmable input current limit and VINDPM battery tracking
- ✓OTG boost mode with output up to 1.2 A
- ✓Hiccup mode overcurrent and output short-circuit protection
- ✓26 mΩ battery switch with ship mode leakage near 2.5 µA
- ✓Battery temperature sensing for charge and boost modes
Specifications
| Brand | SG Micro (SGMICRO) |
|---|---|
| Model | SGM41513 |
| Category | Charging IC (Single-Cell Battery Charger) |
| Compatibility | Single-cell Li-Ion and Li-polymer battery charging circuits |
| Supported Devices | Smartphones, tablets and portable systems |
| Technology | I2C controlled, NVDC power path, 1.5 MHz synchronous buck charger |
| Input Voltage | 3.9 V to 13.5 V operating, up to 22 V sustained |
| Power Rating | 3A charging, OTG boost up to 1.2 A |
| Dimensions | TQFN-4×4-24L package (4 mm × 4 mm) |
Common Repair Uses
- ✓Diagnosing a no-charge fault by checking VBUS against the 3.9 V to 13.5 V window
- ✓Restoring charging on a dead phone after confirming the charger IC output path
- ✓Replacing a faulty charger IC on a board after input and battery path tests pass
- ✓Checking power-on behavior on a deeply depleted battery through instant-on operation
- ✓Testing ship mode and wake-up recovery on boards that stay off after long storage
- ✓Verifying battery temperature sensing when charging stops on a healthy input
- ✓Testing OTG boost output on boards that must supply reverse power to accessories
- ✓Hot air rework of the TQFN-4×4-24L package during board-level IC change
Compatible Devices
- ✓Verified scope is board-level, not device-specific
- ✓Single-cell Li-Ion battery charging circuits
- ✓Single-cell Li-Polymer battery charging circuits
- ✓USB standard hosts and USB 2.0 / USB 3.0 compliant input sources
- ✓High-voltage adapters within the 3.9 V to 13.5 V operating input range
- ✓Smartphone and tablet power boards with NVDC power path architecture
- ✓Portable systems with I2C-controlled charging and OTG boost
- ✓SGM41513A variant boards (verify IC revision marking)
- ✓SGM41513D variant boards (verify IC revision marking)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
What input voltage range does the SGM41513 support?
Does the SGM41513 support I2C control and OTG boost mode?
Related products
339S0223 For iPad 5/Air1 A1474 Wifi IC – U5800 WiFi Module
In stock
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock
U2 Charging iPhone 8, iPhone 8 Plus, iPhone X Chip – 1612A1
In stock



