SMB1395 001 Charging iC – Qualcomm Auxiliary Charger IC

₨ 1,200

Divide-by-2 Charge Pump for High-Current Charging

The SMB1395 001 Charging iC is a Qualcomm divide-by-two charge pump for auxiliary, high-current battery charging. It accepts input from 3.7V to 14V and delivers up to 10A of output, working alongside Qualcomm battery charging PMICs in parallel charger configurations. Programmable input current from 0.5A to 5A, switching frequency from 200kHz to 900kHz, and I²C/SPMI control give technicians spec-level control over the charging path. For repair shops working on Quick Charge 3 and 4 platforms, it is a reference component for board-level charging diagnosis and replacement.

15 People watching this product now!
Description

SMB1395 001 Charging iC overview

The SMB1395 001 Charging iC is a Qualcomm auxiliary converter built on a divide-by-two architecture, designed for 1SnP high-current cable charging. It takes a high-voltage adapter input, halves the voltage, and delivers large charge current into a single-cell lithium-ion battery with low conversion loss. Its dual-branch structure switches the two branches 180 degrees out of phase, which keeps the high-current switching load spread across the converter. The input range is 3.7V to 14V and the output reaches 10A, so it sits in the core of fast-charge designs that push serious current through the phone’s charging path. Verified efficiency is 96.82 percent at a 6A load, which keeps heat rise manageable during long charging sessions. If a board fails to charge under Quick Charge load, this part sits between the adapter and the battery and carries most of the power, so it belongs on your diagnostic list. Programmable switching frequency from 200kHz to 900kHz and programmable input current from 0.5A to 5A in 50mA steps let the design be tuned to the load. Battery charge current equals twice the input current, so the software configuration matters as much as the hardware. The SMB1395 communicates over SPMI and I²C, and multiple devices can operate together while reporting battery current, which is how parallel charger setups are built. In a dual or triple parallel configuration, the SMB1395 works with Qualcomm battery charging PMICs to share the load and raise total charge current. Quick Charge 3, 3+, 4 and 4+ compatibility is handled through software, so the same hardware serves different adapter protocols once firmware negotiates correctly. Remote USB input voltage sensing gives the controller an accurate reading of the voltage at the connector rather than at an internal node. External overvoltage protection FET control provides surge protection up to 350V on the input side. The package is a 15-ball fine-pitch FBGA with a 3 by 5 ball array and 0.4mm ball pitch, with an operating range of minus 30 to 85 degrees Celsius. That package demands controlled rework: use a stencil matched to the 0.4mm pitch, a calibrated hot air station, and flux that prevents ball bridging during reflow. Before replacing the part, rule out upstream faults. A damaged connector, a shorted input capacitor, or a failed battery protection circuit can mimic a dead charge pump. Measure the input rail with the adapter connected, check the expected output voltage, and compare readings against a known-good board of the same model. Because the part handles high current, a weak solder joint heats quickly under load, so inspect every reflowed ball under a microscope before reassembly. The SMB1395 001 Charging iC fits best in a workflow built around charging-path diagnostics on Qualcomm platforms, where the technician measures, isolates, and replaces the converter rather than guessing. Pair it with a hot air station, a microscope, a current-limited DC power supply, and a multimeter with fine probes so each step from measurement to replacement stays controlled. Use this part as the reference point when comparing a suspect board against the design it was built for.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Divide-by-2 charge pump architecture for high-efficiency single-cell charging
  • 96.82% efficiency verified at a 6A load
  • 3.7V to 14V input range with up to 10A output
  • Programmable switching frequency from 200kHz to 900kHz
  • Programmable input current from 0.5A to 5A in 50mA steps
  • I²C and SPMI control interfaces with multi-device battery current reporting
  • Remote USB input voltage sense and external OVP FET control for surge protection up to 350V
  • Quick Charge 3, 3+, 4 and 4+ support through software configuration

Specifications

BrandQualcomm
ModelSMB1395
CategoryCharging IC (Auxiliary Charge Pump / Divide-by-2 Converter)
TechnologyDivide-by-2 charge pump, dual-branch 180° out-of-phase switching
Input Voltage3.7V to 14V
Output CurrentUp to 10A
Efficiency96.82% at 6A load
Switching Frequency200kHz to 900kHz (programmable)
Input Current0.5A to 5A, programmable in 50mA steps
InterfaceI²C and SPMI
Package15-ball FBGA (3×5 array), 0.4mm ball pitch
Operating Temperature−30°C to 85°C

Common Repair Uses

  • Diagnosing no-charge or slow-charge faults on Qualcomm fast-charge boards
  • Replacing a failed auxiliary charge pump in the high-current charging path
  • Verifying input voltage and output behavior during charging-circuit troubleshooting
  • Board-level rework using hot air and microscope inspection on the 0.4mm FBGA package
  • Checking charging behavior under Quick Charge 3 and 4 adapters before and after repair

Compatible Devices

  • Qualcomm battery charging PMIC platforms, in dual or triple parallel charging configurations
  • Quick Charge 3, 3+, 4 and 4+ adapter protocols (via software)
  • Single-cell (1SnP) lithium-ion battery charging circuits
  • High-current cable charging paths with a 3.7V–14V input range
  • Multi-device parallel charging setups with battery current reporting

FAQ

What is the SMB1395 001 Charging iC?
The SMB1395 001 Charging iC is a Qualcomm divide-by-two charge pump used as an auxiliary converter in high-current battery charging circuits.
What is the brand of this product?
The brand of this product is Qualcomm.
What is the model of this product?
The model of this product is SMB1395, supplied under the 001 variant code.
What is this product used for?
This product is used to deliver high charge current to a single-cell lithium-ion battery in parallel or auxiliary charging configurations.
Which devices are compatible with this product?
This product is compatible with Qualcomm battery charging PMIC platforms and Quick Charge 3, 3+, 4 and 4+ adapter protocols through software.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users working on charging circuits.
What input voltage range does the SMB1395 accept?
The SMB1395 accepts an input voltage range of 3.7V to 14V.
Does the SMB1395 support Quick Charge 4 and PPS adapters?
Yes. The SMB1395 is designed for Quick Charge 4 and PPS enabled adapters, with Quick Charge 3, 3+, 4 and 4+ compatibility handled through software configuration.