Mechanic iMini Middle Bezel 2.5 Hollow Cross Bit
₨ 400
Mechanic iMini Middle Bezel 2.5 Hollow Cross Bit for Precise Mobile Phone Screws
This Mechanic iMini middle bezel 2.5 screwdriver bit uses a hollow cross tip sized for the middle plate screws you meet during board-level phone work. The bit is made from chrome-molybdenum steel and holds screws with a strong magnetic grip, so fasteners stay seated while you turn them. The handle is aviation aluminum alloy with an anti-slip, ergonomic shape that keeps your grip steady over long repair sessions. It fits the iMini series handle system and suits technicians who open phones, pull boards, and reassemble frames on a daily basis.
In stock
Mechanic iMini Middle Bezel 2.5 Hollow Cross Bit for Board-Level Phone Repair
The iMini middle bezel 2.5 screwdriver bit targets one specific job on the bench: removing and refitting middle plate screws without stripping the head. Those screws hold the internal frame and board stack in place, and a loose or worn tip turns a quick board pull into a slow, risky session. This bit gives you a defined hollow cross profile at the 2.5 size, so the tip sits deep in the recess and transfers torque cleanly. You use it when a phone is open on your repair mat and you need to free the frame without marring the screw heads that you will reuse.
Hollow Cross Tip Geometry and Seating
A hollow cross tip differs from a standard cross because the center is open, which lets the bit grip the outer walls of the screw recess instead of riding on its peak. Seating the tip fully before you apply pressure is what protects the screw. Set the bit straight, press gently into the recess, and turn slowly until you feel the engagement lock. If the bit wobbles, stop and check the tip for wear before you continue, since a rounded tip is the fastest route to a stripped screw.
Chrome-Molybdenum Steel Bit and Magnetic Hold
The bit is made from chrome-molybdenum steel, a material chosen for toughness under repeated torque cycles. Strong magnetic adsorption keeps the screw attached to the tip during removal, which matters when screws are small and fall easily into a board or a case cavity. Keep the bit clean of metal dust from frame work, because debris on the tip weakens the magnetic grip and makes the screw lift unevenly.
Aviation Aluminum Handle and Working Comfort
The handle is aviation aluminum alloy with an anti-slip, ergonomic profile. Metal handles dissipate heat and resist flex, so the bit holds its alignment through a long session. The grip reduces hand fatigue when you work through a full row of fasteners, and it keeps your control steady when the phone is small and the screws are tight.
Using the Bit in Your Repair Workflow
Place this bit in your middle plate kit, not your general screwdriver tray, so you reach for it at the right moment. Work in a clear order: remove the outer shell, note screw positions, then clear the middle plate screws one at a time with the magnetic bit. Store the screws in a labeled tray matched to their positions so reassembly goes smoothly. After each job, inspect the tip under good light and replace it when the edges round over, because a worn bit damages screw heads and slows every later repair.
Compatibility Scope and Safe Use
This bit is a tip-type tool, and its fit depends on the screw you are removing. Confirm the screw head matches a hollow cross 2.5 profile before applying force. Do not use it on screws that clearly show a different recess shape, and do not force a mismatched bit into a worn head. Pair the bit with a stable bench, good lighting, and a clean mat so the tip stays aligned during removal.
| Weight | 0.11 kg |
|---|
Key Features
- ✓Hollow cross tip profile at the 2.5 size
- ✓Chrome-molybdenum steel bit for repeated torque use
- ✓Strong magnetic adsorption holds screws during removal
- ✓Aviation aluminum alloy handle for low weight and stable alignment
- ✓Anti-slip, ergonomic grip for long sessions
- ✓Fits the iMini series handle system
- ✓Suited to middle plate work in phone board repair
- ✓Simple swap-in bit for the iMini series handle
Specifications
| Brand | MECHANIC |
|---|---|
| Model | iMini Series |
| Category | Precision Screwdriver Bit |
| Technology | Strong magnetic adsorption |
| Material | Bit: chrome-molybdenum steel; Handle: aviation aluminum alloy |
| Tip Type | Hollow cross |
| Tip Size | 2.5 |
Common Repair Uses
- ✓Removing middle plate screws to separate the frame from the board
- ✓Refitting middle plate screws during phone reassembly
- ✓Clearing a board stack for IC or PCB-level repair work
- ✓Taking out screws without stripping the head on repeat jobs
- ✓Magnetic retention for small screws during open-case service
- ✓Organizing fasteners by position during multi-screw disassembly
Compatible Devices
- ✓Middle plate screws in mobile phone internal frames (tip-type scope)
- ✓Hollow cross 2.5 recess fasteners used during board-level disassembly (tip-type scope)
- ✓Universal across phone brands only where the recess size matches
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is the bit magnetic?
What steel is the bit made from?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



