MECHANIC XP2 148C Low Temperature Solder Paste 20g

₨ 1

Low Temperature Paste for Layered iPhone Boards

MECHANIC XP2 is a 148C low temperature solder paste built for logic board work on layered iPhone X-series motherboards. Its melting point sits well below standard alloys, so you limit heat exposure on nearby components while you solder. The 20g plastic jar holds a moderately viscous paste that stays where you place it. Distributor listings describe bright, full joints with minimal residue when you apply it correctly. Use it for reballing, pad repair and jumper work where precision matters more than volume. Pair it with a hot air station and a microscope for controlled results on dense boards.

Out of stock

14 People watching this product now!
Description

MECHANIC XP2 148C Low Temperature Solder Paste for Logic Board Repair

The MECHANIC XP2 is a 148C low temperature solder paste designed for the layered logic boards found in the iPhone X series. A melting point of 148°C sits well below what standard alloys need, which lowers thermal stress on surrounding components during sandwich board repairs. Choosing the right melting point is the first decision in any low-temperature job, and this paste gives you a dependable option in that range. The 20g jar suits a repair bench that handles steady logic board work rather than bulk production.

Key Technical Highlights

The XP2 belongs to MECHANIC’s 148°C range, so you get a melting point that stays well under standard lead-based alloys. Its viscosity rating of 178 ±10 keeps the paste firm enough to hold its shape on a pad while you position components. The particle range of 20 to 38 microns suits fine-pitch pads and small reballing grids, where uneven particles cause bridging. The paste ships in a plastic jar with an air-seal insert, which slows drying between sessions. Distributor listings describe high wettability, meaning the paste flows into pad edges and forms full joints without pulling away. These specifications matter most when you compare this paste with a general-purpose alloy, because the lower melting point changes how you set your heat profile from the first joint onward.

Repair Workflow Fit

Reach for the XP2 at the stage where the faulty chip is already removed and the pads are clean and flat. Apply a thin, even layer with a stencil or a fine tip, then bring the area up to temperature with your hot air station rather than a fast, concentrated blast. Keep the heat low and steady so nearby components keep their existing joints. Check the pads under a microscope before you power the board, because a bridge or a dry joint shows up far more clearly at magnification than under a bench lamp. Once the board cools, wipe the area with isopropyl alcohol to lift flux residue. Build a repeatable routine around a PCB holder and a reballing kit from our range, so every board gets the same setup and the same inspection steps.

Where It Fits on Your Bench

Shops that handle iPhone X, XS, XS Max, and XR logic boards get the most value from this paste, because those boards use layered construction that rewards low-temperature technique. Service centers training technicians on sandwich board soldering can use it to teach a controlled, repeatable process with one material. Repair businesses buying in volume should note that the 20g jar suits daily logic board work rather than production runs, so plan your restocking around actual job counts. Because the melting point sits below standard alloys, build your reflow settings around 148°C instead of the defaults you use for leaded or mid-range pastes. Test your settings on a scrap board before you commit a customer’s device. Run one practice joint at a time until your temperature and timing feel consistent, then move to live repairs.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Low melting point of 148°C for heat-sensitive layered boards
  • Particle range of 20 to 38 microns for fine-pitch work
  • Moderate viscosity that holds position on pads
  • High wettability for full, bright joints (per distributor listing)
  • Plastic jar with air-seal insert to limit drying
  • 20g quantity for steady repair bench use

Specifications

BrandMECHANIC
ModelXP2
CategorySolder Paste (Low Temperature)
CompatibilityiPhone X series logic boards (layered motherboards)
Supported DevicesiPhone X, iPhone XR, iPhone XS, iPhone XS Max
TechnologyLow temperature solder paste, 148°C melting point, viscosity 178 ±10
Weight20g

Common Repair Uses

  • Logic board soldering on layered iPhone X-series boards
  • Reballing and fine-pitch pad repair
  • Jumper and track repair where joints need controlled heat
  • Correcting false or dry solder joints on dense boards

Compatible Devices

  • iPhone X
  • iPhone XR
  • iPhone XS
  • iPhone XS Max
  • Layered (sandwich) logic boards in the iPhone X series

FAQ

What is the product name?
The product name is MECHANIC XP2 148C Low Temperature Solder Paste 20g.
What is the brand of this product?
The brand of this product is MECHANIC.
What is the model of this product?
The model of this product is XP2.
What is this product used for?
This product is used for soldering and pad repair on layered logic boards, including iPhone X-series motherboards.
Which devices are compatible with this product?
This product is compatible with iPhone X, iPhone XR, iPhone XS, and iPhone XS Max logic boards.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Does this paste melt at a low temperature?
Yes, the XP2 has a melting point of 148°C.
What particle size does the XP2 paste use?
The XP2 paste uses a particle range of 20 to 38 microns.