Kada 2018D+ Heat Gun Handle Replacement
₨ 1,600
Hot Air Gun Handle Replacement for Your Rework Bench
When the handle on your hot air station fails, the whole station often sits idle. This 8-hole handle carries the heating core, magnetic switch, temperature sensor and power cord in one assembly. You swap the old handle for this one and the station runs again. It measures about 24 x 4 x 2 cm, comes in black, and includes one handle with a long power cord for free movement at the bench.
Out of stock
Hot Air Gun Handle Replacement Built Around the Heating Core
Hot air gun handle replacement is a routine job on any busy repair bench, and the handle is where most station faults show up first. This replacement handle gives you a direct swap for the factory unit. Lift it and the magnetic switch starts the airflow. Return it to the holder and the heat cuts off. Your workflow stays the same, and the station gets back to SMD desoldering without a full unit replacement.
What the Handle Contains
Each handle houses the heating core, the magnetic switch, the temperature sensor and the power cord in one housing. The heating core drives the hot air output, while the sensor feeds temperature readings back to the station’s control board. The magnetic switch tells the station when you pick up or set down the handle. Because all three functions sit in one assembly, a single fault in the handle can stop the station, so replacing the complete handle is more practical than repairing individual parts at the bench.
Compatibility Scope and Fit Check
The verified scope for this handle is the 8-hole, 4-core connector family used on 858, 858D, 878A, 878D and 878D+ rework stations. Before you order, compare the connector on your old handle with the 8-hole design, and count the wires on the station’s socket. Confirm the Kada 2018D+ fit with your supplier, because the 2018D+ model is not listed in any source we verified. A mismatch in connector layout can damage the control board, so do not force a fit.
Installing and Testing on Your Bench
Disconnect the station from power and let the handle cool before removing the old unit. Match each wire to its connector pin, and check continuity on the heating and sensor circuits before you reconnect the station. After installation, test the airflow at a low setting, confirm the magnetic switch starts and stops the air when you lift and return the handle, and watch the temperature reading stabilize. Run the new handle at a moderate setting for a few minutes before you return the station to production work.
Why Replace the Handle Instead of the Station
A handle costs far less than a complete rework station, and it restores full function to a station with a damaged heater or switch. Your existing control unit, nozzles and stand stay in service. For shops running several stations, keeping spare handles on the shelf cuts downtime when a unit fails mid-job. You protect your investment in the station body while the handle takes the wear that comes from daily use.
| Weight | 1.0 kg |
|---|
Key Features
- ✓Heating core, magnetic switch, temperature sensor and power cord in one handle
- ✓Direct replacement for factory handles on compatible stations
- ✓Solid, durable construction for daily bench use
- ✓Black finish, 24 x 4 x 2 cm
- ✓Ultra-long power cord for flexible movement
- ✓Single-part swap that restores full station function
Specifications
| Category | Hot Air Gun Handles |
|---|---|
| Model | Kada 2018D+ (verify fit before publishing) |
| Compatibility | 858 / 858D / 878A / 878D / 878D+ rework stations |
| Technology | Heating core, magnetic switch, temperature sensor |
| Dimensions | 24 x 4 x 2 cm |
| Weight | 208 g |
| Connector | 8-hole, 4-core |
Common Repair Uses
- ✓Replacing a dead or unresponsive hot air handle on a rework station
- ✓Restoring airflow when the heating core fails
- ✓Fixing a magnetic switch that does not start or stop the airflow
- ✓Correcting temperature readings from a faulty sensor
- ✓Removing SMD resistors and capacitors during board repair
- ✓Replacing ICs and other surface-mount components on mobile PCBs
Compatible Devices
- ✓8-hole handle family for 858, 858D, 878A, 878D and 878D+ rework stations
- ✓858 hot air rework station
- ✓858D hot air rework station
- ✓878A hot air rework station
- ✓878D hot air rework station
- ✓878D+ hot air rework station
- ✓8-hole, 4-core handle connector type
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does this handle include a temperature sensor?
Which stations use the 8-hole handle connector?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



