Mechanic SD360 Max No-Clean Solder Oil Flux 10cc

₨ 1,500

SD360 Max No-Clean Flux for BGA and SMD Soldering

The Mechanic SD360 Max gives your repair bench a no-clean, transparent solder oil flux for BGA, SMD, and PCB work. You apply a thin layer before reflow or reballing, and the flux helps the solder wet the pads while keeping oxidation off the copper. The formula produces light smoke and a mild odor, so you can work through a full session without fighting fumes. The residue stays clear and non-corrosive, which lets you skip the post-solder cleaning step on most jobs. The 10cc push-rod syringe gives you controlled dosing on tight chip pads. Use it on mobile motherboards, laptop boards, and LED PCBs, with either lead or lead-free solder.

Out of stock

14 People watching this product now!
Description

Mechanic SD360 Max No-Clean Solder Oil Flux for Mobile and PCB Repair

Every BGA and SMD job depends on how well the solder flows, and the SD360 Max no-clean flux gives you a dependable starting point on the board. Your workflow improves when the flux keeps oxidation from forming on the pads and lets the solder spread evenly across each joint. This Mechanic oil flux suits technicians working on mobile motherboards, laptop boards, and LED PCBs. Whether you run a small repair counter or a full service center, you get one flux that works with both lead and lead-free solder. The transparent formula keeps your view clear, so you can inspect every joint after reflow. Treat it as a consumable that supports each stage of your reballing and component replacement process.

Where SD360 Max Fits in Your BGA and SMD Workflow

Most SD360 Max sessions start before the hot air touches the board. You clean the old solder off the pads, check the chip footprint under your microscope, and then apply a light coat of flux to the pad area. For BGA reballing, the flux holds the balls in place while the chip heats, so each ball seats cleanly on its pad. For SMD work, such as replacing a capacitor or resistor on a phone motherboard, a small dot of flux helps the new component sit flat and solder evenly. On a dead phone where you need a jumper or a trace repair, you can use the same flux to coat the copper before tinning. Because it keeps oxidation from forming during heating, it lowers the risk of cold joints. Keep the syringe cap on between jobs so the paste stays consistent.

Low-Smoke, Transparent Formula That Keeps Joints Clean

A clear residue matters on a crowded board. With SD360 Max, you can inspect the joint under magnification without the film that darker fluxes leave behind. The formula produces light smoke and a mild smell, which makes it easier to work in a small room without a fume extractor. The non-corrosive, no-clean chemistry means you do not need to wash most boards after reflow. That saves time on high-volume bench work and keeps boards away from cleaning baths that can wear down labels and connectors. The paste flows smoothly and wets the pads well, which supports stronger adhesion on the finished joint. Lead and lead-free solder both respond well to this flux, so you can keep one bottle at the bench for mixed jobs.

Dosing, Storage, and Handling on Your Bench

The push-rod syringe gives you control over how much flux reaches the board. Press the plunger slowly and dispense a small bead, which avoids flooding fine-pitch pads and bridging between tiny IC legs. Wipe the tip after each use, because dried flux can clog the nozzle and block the next application. Store the syringe upright in a cool spot away from direct sunlight, and cap it tightly after every session. A single 10cc syringe lasts through many small jobs, and your usage per board sets the pace. Test a small area on a scrap board before you apply the flux to a customer’s motherboard, especially when you switch between lead and lead-free solder.

Additional information
Weight0.5 kg
Q & A
Please login to post questions

Key Features

  • No-clean formula that leaves minimal, non-corrosive residue after reflow
  • Transparent paste that keeps joints visible for inspection
  • Low smoke and light smell for comfortable bench work
  • Compatible with both lead and lead-free solder
  • Oxidation prevention that supports consistent, solid joints
  • Good paste fluidity and wetting for stronger solder adhesion
  • 10cc push-rod syringe for controlled, precise dosing
  • Suits BGA reballing, SMD replacement, and general PCB repair

Specifications

BrandMechanic
ModelSD360 Max
CategorySoldering Flux
CompatibilityUniversal, not device-specific
Supported DevicesMobile phone and laptop motherboards, BGA and SMD components, LED PCBs
TechnologyNo-clean transparent flux with high-activity additives, lead and lead-free compatible

Common Repair Uses

  • Verified real-world workflows for this flux.
  • BGA reballing on CPU, power IC, and audio IC footprints
  • Applying flux before hot air reflow of replacement chips
  • Tinning copper pads and traces during jumper work
  • SMD capacitor and resistor replacement on phone motherboards
  • Repairing dead phones after failed chip replacement
  • Laptop motherboard component replacement
  • LED PCB repair and component reflow
  • Fine-pitch pad preparation before soldering

Compatible Devices

  • Universal, not device-specific. Scope is general PCB soldering.
  • Mobile phone motherboards for chip-level repair
  • Laptop motherboards
  • BGA chips during reballing and reflow
  • SMD components such as capacitors and resistors
  • LED PCB boards
  • Lead-based solder joints
  • Lead-free solder joints
  • Power and audio ICs during replacement

FAQ

What is the product name?
The product name is Mechanic SD360 Max No-Clean Solder Oil Flux 10cc.
What is the brand of this product?
The brand of this product is Mechanic.
What is the model of this product?
The model of this product is SD360 Max.
What is this product used for?
This product supports BGA reballing, SMD component replacement, and general PCB soldering.
Which devices are compatible with this product?
This product is universal and not device-specific. It suits mobile phone and laptop motherboards, BGA and SMD components, and LED PCBs.
Who should use this product?
This product suits mobile repair technicians, repair shops, service centers, and professional users.
Does SD360 Max flux work with lead-free solder?
Yes. The flux works with both lead and lead-free solder processes.
Do I need to clean the board after using SD360 Max flux?
Most boards do not need cleaning because the no-clean residue is transparent and non-corrosive.