Youtools UT-07W Rotating Screwdriver Storage Box

₨ 2,500

Rotating Screwdriver Holder for Mobile Repair Benches

The UT-07W gives your bench one place for every driver and tweezer. Its 12 holes keep each tool upright and separated, so you pick the right tip without pulling out three wrong ones first. A double bearing shaft in the base lets the top tilt up to 155° while the whole unit turns a full 360°. You spin the holder toward your hands rather than leaning across your repair station. The footprint stays small enough to sit beside your soldering iron and microscope. It replaces loose drawers and scattered trays on busy benches.

In stock

19 People watching this product now!
Description

Organizing Your Screwdrivers and Tweezers on the Bench

A rotating screwdriver holder for mobile repair earns its place when your bench stops losing time to searching. The Youtools UT-07W screwdriver holder combines a 12-hole layout with a double bearing base, so you keep screwdrivers and tweezers standing upright and within reach during a job. Most technicians know the drawer routine: a device sits open, the tip you need is buried, and the job drags. Keeping every tool in a fixed position changes that rhythm. Your hands stay on the device while your eyes find the right tip. The sections below cover how the holder is laid out, how the base moves, and how it fits into a repair routine.

Twelve Holes That Keep Every Tool Upright

The UT-07W gives you 12 holes, and each one holds a single driver or a pair of tweezers. Once you assign a tip to a hole, it stays there, so your hand learns the position and you stop hunting through a pile. The holes keep each tool upright and separated, which protects fine tips from knocking against each other on a crowded bench. The product page lists Phillips, flathead, Torx, pentalobe, and tri-point drivers among the tools it accommodates, which covers most phone teardown work. Tweezers share the same layout, so you avoid a separate tray for component placement on the board. Before you commit your full set, load a few drivers and check that each seats without wobbling. That quick test takes less than a minute and saves you from reorganizing later.

How the Double Bearing Base Changes Your Reach

The base houses an imported upper and lower double bearing shaft, and that mechanism sets this holder apart from a static block with holes. The top section tilts up to 155°, so you angle the drivers toward your seat instead of leaning over the device. The entire unit rotates a full 360°, which lets you turn the holder toward whoever needs a driver at the moment. A rotating base also suits a shared workshop, where a fixed tray only faces one technician. The product page states that tools stay in their holes during tilting, and that claim is worth testing with your own drivers. Position the holder on a stable surface before you tilt it, and keep it clear of the soldering iron tip and hot air airflow. Rotate it slowly the first few times so you learn how much clearance your bench allows.

Building a Routine from Teardown to Reassembly

A tool holder pays off most when it follows the order of a repair. During teardown, you pull the drivers you need for the first screws and leave them in their holes, so the set reflects the job in front of you. Tweezers stay in the same unit, which keeps small components and screws within reach while you work. This screwdriver storage box fits the usual phone repair sequence, from screen and back panel removal through board-level handling. Technicians working on iPhone opening, Android back panels, or PCB component work switch tools often, and a fixed holder cuts that switching time. During reassembly, each driver returns to its own hole, so the next job starts from a clean bench. The holder weighs 0.29 kg, which makes it easy to move between stations when your bench layout changes. Keep it in the same corner every day, so your hand finds it without looking.

Additional information
Weight0.29 kg
Q & A
Please login to post questions

Key Features

  • 12-hole layout for screwdrivers and tweezers
  • Imported upper and lower double bearing shaft
  • Tilts up to 155° without dislodging stored tools
  • Full 360° base rotation for access from any side
  • Compact footprint for crowded repair benches
  • Upright, visible tool storage for quick identification
  • Ready to use with no assembly required
  • Suitable for shared workstations

Specifications

BrandYoutools
ModelUT-07W
CategoryMobile Repair Soldering Accessories
CompatibilityUniversal, not device-specific
Supported DevicesPrecision screwdrivers and tweezers (12 holes)
TechnologyDouble bearing shaft with 155° tilt and 360° base rotation
Weight0.29 kg

Common Repair Uses

  • Phone disassembly, reassembly, and bench tool management.
  • Organizing screwdrivers during phone disassembly
  • Keeping drivers ready for reassembly of the same device
  • Screen and back panel removal workflows
  • Handling tweezers for small component placement on PCBs
  • Quick tool switching during iPhone and Android teardown
  • Bench organization for shared repair workshops
  • Keeping screwdrivers out of drawers during service work
  • Tool management at a dedicated repair station

Compatible Devices

  • Universal. Works with standard precision tools rather than a single phone model.
  • Universal, not device-specific: works with standard precision tools rather than a single phone model
  • Phillips precision screwdrivers
  • Flathead precision screwdrivers
  • Torx precision screwdrivers
  • Pentalobe screwdrivers
  • Tri-point screwdrivers
  • Precision tweezers
  • Up to 12 tools in the 12-hole layout

FAQ

What is the product name?
The product name is Youtools UT-07W Rotating Base Screwdriver Storage Box.
What is the brand of this product?
The brand of this product is Youtools.
What is the model of this product?
The model of this product is UT-07W.
What is this product used for?
This product is used for organizing and storing screwdrivers and tweezers on a mobile repair bench.
Which devices are compatible with this product?
This product is universal and works with standard precision screwdrivers and tweezers, not a specific phone model.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
How many screwdrivers fit in a 12-hole rotating screwdriver holder?
The UT-07W holds up to 12 tools, one per hole, including screwdrivers and tweezers.
Does a double bearing screwdriver holder stay steady when tilted?
The double bearing shaft lets the top section tilt up to 155° while stored tools remain in their holes, according to the product page.