2UUL DW01 Mobi Desoldering Wick 2015 (5 Rolls/Box)

₨ 1,499

2UUL DW01 Mobi Solder Wick Box

The 2UUL DW01 desoldering wick gives your bench a clean way to pull leftover tin off mobile phone boards. Each Mobi 2015 roll measures 2.0 mm wide and 1.5 m long, and the box holds five rolls. You press the braid onto the joint, touch it with a hot iron, and the copper weave soaks up molten solder through capillary action. Use it after IC change karna jobs, for BGA CPU and NAND pad cleanup, and for removing solder bridges between pins. The braid keeps your pads flat and ready for reballing or a fresh chip.

In stock

17 People watching this product now!
Description

2UUL DW01 Desoldering Wick for Mobile Board Rework

The 2UUL DW01 desoldering wick removes excess tin from phone motherboards with nothing more than a soldering iron and a steady hand. Each roll of this Mobi 2015 braid measures 2.0 mm wide and 1.5 m long, and the box holds five rolls. A workshop that handles chip-off and pad-cleaning jobs every day gets a reliable supply of fresh copper braid without frequent reorders. The braided copper pulls molten solder along its weave through capillary action, so a lumpy pad turns into a smooth surface that accepts a new chip or a reballing stencil.

How the 2.0 mm Braid Handles Pad Cleaning

You lay the braid flat over the solder you want to remove, press a heated iron tip on top of it, and watch the tin flow into the copper. Once the braid loads with solder, you cut the used section with nippers and continue on clean braid. This routine keeps every pass as effective as the first one and prevents you from dragging old tin back across the pad.

The 2.0 mm width covers a full row of pads, or the leftover tin under a removed BGA CPU, NAND or eMMC chip, in one controlled pass. That saves heat cycles, which matters on a multilayer board where repeated heating weakens pads. The flexible braid also follows tight spots near shields and connectors, so you reach areas where a solder sucker does not fit.

Heat discipline decides the result. Keep the iron on the braid for no more than 5 seconds at a time. Longer contact risks damage to nearby components and the PCB. Drag in short, smooth strokes, lift the braid while the solder is still molten, and never pull it off a cooled joint, because that tears pads away from the board.

Where It Fits in the Repair Workflow

After you lift a chip with a hot air station, the pads carry uneven solder. Level them with this wick before you place the new IC or start reballing. Clean, flat pads let the new solder balls seat evenly and reduce the chance of a dead phone returning with a hardware fault after reassembly.

Solder bridges between fine pins cause many charging issue and no-power complaints. Wick removes the bridge without moving neighbouring components, and a quick multimeter check afterward confirms the short has gone. Technicians who chase a hang on logo or dead after flash fault down to a reflowed eMMC or NAND also rely on wick to clean the pads before reattaching the chip.

The wick works best as part of a complete rework setup. Pair it with a soldering station, a hot air station, a microscope for pad inspection, a PCB holder to steady the board, and a reballing kit for the final reattachment. Together they cover the full removal, cleaning and refitting sequence on a phone board.

Why the 5-Roll Box Suits a Busy Workshop

Braid disappears quickly in a shop that services dozens of boards a week. A box of five 1.5 m rolls gives you roughly 7.5 m of wick in total, enough to keep one roll on the main bench, one in the field toolkit and spares in stock. Each roll stays separate, so you open a new one only when you need it. The 2015 specification (2.0 mm by 1.5 m) also gives you one consistent size across your whole team, so every technician cleans pads the same way and no one wastes time hunting for the right width.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 2.0 mm wide copper braid for pad rows and chip footprints
  • 1.5 m length on every roll
  • Five separate rolls in one box
  • Capillary action draws molten solder off the board
  • Flexible braid reaches tight spots
  • Works with any soldering iron
  • Cuts to length with nippers
  • Supports BGA, CPU and NAND pad cleaning

Specifications

Brand2UUL
ModelDW01 Mobi 2015
CategoryDesoldering Wick / Solder Wick
CompatibilityUniversal – works with a soldering iron on any PCB
Supported DevicesMobile phone motherboards and PCBs
TechnologyBraided copper capillary action
MaterialCopper braid
Dimensions2.0 mm width x 1.5 m length per roll
Packaging5 rolls per box

Common Repair Uses

  • Removing leftover solder from pads and pins during mobile board repair
  • IC change karna pad cleanup
  • Reballing preparation
  • CPU chip tin removal
  • NAND and eMMC pad cleaning
  • Solder bridge removal
  • Charging port pad cleanup
  • Excess solder removal after hot air chip lift
  • Motherboard solder joint cleaning

Compatible Devices

  • Universal consumable – not device-specific; suits any board you clean with a soldering iron
  • Smartphone motherboards
  • BGA CPU pads
  • NAND and eMMC chip pads
  • SMD component pads
  • Through-hole joints
  • Pin rows on connectors
  • General electronics PCBs
  • BGA solder joint areas

FAQ

What is the product name?
The product name is 2UUL DW01 Mobi Desoldering Wick 2015 (5 Rolls/Box).
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is DW01 Mobi 2015.
What is this product used for?
This product removes excess solder from mobile phone PCB pads, chip footprints and solder bridges.
Which devices are compatible with this product?
This product is a universal consumable. It works on any mobile phone motherboard or PCB that you clean with a soldering iron.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What width and length is the 2UUL DW01 desoldering wick, and which pads does it suit?
Each roll measures 2.0 mm wide and 1.5 m long. The width covers pad rows and the tin left under BGA CPU, NAND and eMMC chip footprints.
How long can I heat the 2UUL DW01 wick on a joint?
Keep the iron on the braid for no more than 5 seconds at a time. Longer contact risks damage to nearby components and the PCB.