One-Stop LCD Cutting Wire 0.03mm (1000M)
₨ 999
0.03mm LCD Screen Separation Wire
The One-Stop LCD cutting wire 0.03mm comes on a 1000M spool, built for technicians who separate glass from LCD and OLED panels every day. The ultra-fine 0.03mm diameter cuts a narrow path through the adhesive layer, so you work on flat, curved, and edge screens with less risk to the display underneath. The long spool covers high-volume screen refurbishing and keeps your bench stocked without frequent reel changes. Use it freehand or with a separator machine. If you run a repair shop or service center in Pakistan, this wire gives you a precise, workshop-ready consumable for broken glass jobs.
Out of stock
Precision LCD Cutting Wire 0.03mm for Screen Separation
The One-Stop LCD cutting wire 0.03mm gives your bench an ultra-fine line for separating cracked glass from the LCD or OLED panel underneath. At 1000 meters per spool, it suits a repair counter that runs screen refurbishing every day, so you stop reordering short 100M reels. You pull a length, cut through the adhesive layer, and lift the glass without forcing the display. Technicians who handle display problem jobs on flat, curved, and edge screens choose this diameter because it slices a narrow channel and leaves the panel intact.
Why 0.03mm Matters on Delicate Panels
Wire diameter decides how much material you remove and how much drag you feel inside the adhesive. A 0.03mm line cuts a narrower path than the common 0.05mm, 0.08mm, and 0.1mm options, which suits thin panels and tight edge-screen assemblies. You trade some forgiveness for that precision. Thinner wire asks for steady hands, even tension, and a smooth pull, so you keep the cut straight and avoid snagging the panel edge. Once you build that rhythm, the 0.03mm size gives you cleaner separations on screens where heavier wire leaves little margin.
1000M Spool for Workshop Volume
A 1000M spool changes your cost per job. You cut a fresh section for each screen, because a smooth, undamaged wire separates cleaner than a kinked or worn one. Discard the section you used, pull a new length, and move to the next screen. Heavy workshops, wholesale technicians, and service centers that process dozens of broken-glass screens each week get the most from this size. Store the spool in a dry spot and keep the loose end controlled, so the wire does not tangle or kink before you use it. You can run it freehand with handles or mount it on a separator machine that holds the wire under tension.
Where It Fits in Your Repair Workflow
Glass replacement on a working LCD or OLED starts with separation. You warm the screen with a heating plate or a controlled hot air station to soften the adhesive, then pull the wire through the layer between the glass and the display matrix. A microscope helps you check the edge for leftover adhesive and hairline damage. A PCB holder or fixture keeps the frame steady while you clean it. This wire handles the cutting stage of that chain, and the tools around it handle heating, inspection, and bonding. It addresses hardware fault cases where the glass breaks but the display still works, which saves you the cost of a full panel swap.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Ultra-fine 0.03mm wire diameter
- ✓1000M spool length for high-volume use
- ✓Narrow cutting path for precise separation
- ✓Suits LCD and OLED glass separation
- ✓Works on flat, curved, and edge screen assemblies
- ✓Usable freehand or with a separator machine
- ✓Cut a fresh section per job for a smooth pull
- ✓Fits mobile phone and tablet repair workflows
Specifications
| Brand | One-Stop |
|---|---|
| Category | LCD Screen Separation Tools / Cutting Wire |
| Compatibility | Universal LCD/OLED screen separation — not device-specific |
| Wire Diameter | 0.03mm |
| Wire Length | 1000M |
Common Repair Uses
- ✓Separating glass from the display panel during screen refurbishing and glass replacement
- ✓Broken front glass removal on working LCD panels
- ✓Broken front glass removal on working OLED panels
- ✓Curved-edge screen separation
- ✓Cutting through OCA/LOCA adhesive layers
- ✓Screen refurbishing for resale
- ✓Tablet glass separation
- ✓Display problem repair when only the glass is cracked
- ✓Bulk screen separation in high-volume workshops
Compatible Devices
- ✓Universal for LCD/OLED glass separation on smartphones and tablets — not limited to a single brand or model
- ✓Smartphone LCD screens
- ✓Smartphone OLED screens
- ✓Tablet display assemblies
- ✓Flat screen assemblies
- ✓Curved screen assemblies
- ✓Edge display assemblies
- ✓Samsung display assemblies
- ✓iPhone display assemblies
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Should I choose 0.03mm or a thicker wire for LCD separation?
Can I use 0.03mm cutting wire without a separator machine?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



