One-Stop LCD Cutting Wire 0.04mm 1000M

₨ 999

LCD Cutting Wire for Glass Separation

The One-Stop LCD cutting wire 0.04mm on a 1000M spool gives your screen refurbishing bench a long, ultra-fine separation line. The 0.04mm diameter slides into the bond line between digitizer glass and LCD panel, then cuts through OCA or LOCA adhesive with steady pressure. You use it freehand with a holder or fit it to a wire-based LCD separator machine. The 1000M length keeps high-volume benches cutting without constant spool changes. Pair it with a heating platform, Hot Air Stations, and a microscope to protect the polarizer layer during every separation.

Out of stock

18 People watching this product now!
Description

LCD Cutting Wire 0.04mm 1000M for Precision Screen Separation

The One-Stop LCD cutting wire 0.04mm 1000M gives screen refurbishers a long, ultra-fine line for separating front glass from the LCD panel. At 0.04mm, the wire enters the bond line between the digitizer glass and the display matrix, then slices through OCA or LOCA adhesive without prying the stack apart. Cracked glass over a working LCD is one of the most common display problems on a refurbishing bench, and a clean separation decides whether you save the panel or scrap it. The 1000M spool suits workshops and refurbishing units that separate panels every day and cannot stop for short spools.

Where 0.04mm Sits in the Cutting Wire Range

Cutting wires run from roughly 0.028mm up to 0.1mm. Technician guidance commonly reserves wires below 0.04mm for straight and curved OLED separation, and wires above 0.04mm for LCD panels. The 0.04mm diameter sits at that boundary. You get a line thin enough to enter tight glass-to-panel gaps, with enough strength to hold under the steady pull an LCD stack demands. Choose a 0.03mm or finer wire when you handle curved OLED edges, and keep this spool for LCD glass replacement and digitizer separation.

Workflow on Your Repair Bench

Separation starts with softening the adhesive. Warm the panel on a heating platform or apply controlled heat with Hot Air Stations, then feed the wire under the glass and draw it across the bond line in short, even strokes. Mount the wire on a handle or holder, or load it into a wire-based LCD separator machine, whichever your bench runs. Keep the line taut, because slack wire wanders and scores the polarizer. Once the glass lifts, check the exposed polarizer under one of your Microscopes before you clean the residue. A scratch at this stage ends the refurbishing job, so inspection saves you a rework.

Why a 1000M Spool Suits Volume Work

Cutting wire wears and breaks as it works, so you replace the working length often. A 1000M spool lets you cut fresh wire for every panel without reordering mid-week. One spool also keeps a single diameter across every job, which keeps your cutting feel and your results consistent from the first panel to the last. Refurbishing units that handle iPhone and Samsung LCD assemblies, tablet panels, and mixed batches of glass replacement work gain the most from that consistency.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Ultra-fine 0.04mm diameter for entry into tight glass-to-LCD gaps
  • 1000M spool length for high-volume refurbishing benches
  • Cuts OCA and LOCA adhesive between glass and LCD panel
  • Works freehand with a holder or in a wire-based separator machine
  • Boundary diameter between OLED-grade and LCD-grade wires
  • Single diameter across the full spool for consistent cutting feel
  • Suits smartphone and tablet LCD glass replacement
  • Supports clean separation that protects the polarizer layer

Specifications

BrandOne-Stop
CategoryLCD Screen Separation Cutting Wire
CompatibilityLCD glass separation, freehand with a holder or in a wire-based separator machine
Supported DevicesSmartphone and tablet LCD screens
DimensionsWire diameter 0.04mm, length 1000M

Common Repair Uses

  • Glass-to-LCD separation in screen refurbishing and glass replacement
  • Removing cracked front glass from a working LCD
  • Separating the digitizer from the display matrix
  • Cutting through OCA adhesive layers
  • Cutting through LOCA adhesive layers
  • Screen refurbishing for resale batches
  • Tablet screen glass replacement
  • Freehand separation with a holder
  • Wire replacement on LCD separator machines

Compatible Devices

  • Smartphone and tablet LCD screens (universal wire, not model-specific)
  • Smartphone LCD assemblies
  • Tablet LCD assemblies
  • iPhone LCD screens
  • Samsung LCD screens
  • OCA-bonded glass and LCD stacks
  • LOCA-bonded glass and LCD stacks
  • Touch panel and digitizer glass assemblies
  • Wire-based LCD separator machines

FAQ

What is the product name?
The product name is One-Stop LCD Cutting Wire 0.04mm (1000M).
What is the brand of this product?
The brand of this product is One-Stop.
What is the model of this product?
This product is the 0.04mm diameter, 1000M length version of the One-Stop LCD cutting wire.
What is this product used for?
This product separates front glass from the LCD panel by cutting through the OCA or LOCA adhesive layer during screen refurbishing and glass replacement.
Which devices are compatible with this product?
This wire works on smartphone and tablet LCD screens, including iPhone and Samsung LCD assemblies. It is universal and not tied to specific models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Is 0.04mm cutting wire suitable for curved OLED screens?
Common technician guidance uses wires below 0.04mm for straight and curved OLED screens and wires above 0.04mm for LCD screens. The 0.04mm diameter sits at the boundary, so use this spool for LCD work and choose a 0.03mm or finer wire for curved OLED edges.
Can I use this cutting wire freehand or in an LCD separator machine?
You can use this wire freehand with a handle or holder, or load it into a wire-based LCD separator machine. Check that your machine accepts a spool of this size and diameter before you load it.