OSS T12-BLS Soldering Iron Tip for T12 Stations

₨ 800

OSS T12-BLS Soldering Tip

The OSS T12-BLS soldering iron tip gives your T12 digital station fast thermal conductivity and steady temperature control for precision board work. A surface coating on the tip end helps it resist blackening at working temperature, and it tins cleanly and wets well. You use it for jumper lagana, charging port pad rework, and small component replacement on dead phone boards. OSS Team supplies it as a single 15 cm replacement tip. It suits technicians who already run a T12-series station and want a dependable spare for daily bench work in Pakistan’s repair shops.

In stock

17 People watching this product now!
Description

OSS T12-BLS Soldering Iron Tip for Precision Board Work

The OSS T12-BLS soldering iron tip gives your T12 station a dedicated precision tip for the jobs that decide whether a repair holds: jumper lagana on a damaged track, pad rework around a charging port, and small component replacement on a dead phone board. You push it into a T12 handle, set your temperature, and start working within seconds, because the heater and sensor sit inside the tip itself. Mechanicpk stocks it for technicians who already run a T12 digital station and need a reliable consumable on the bench.

Heat Delivery and Temperature Response

A T12 tip combines the heating element, the temperature sensor, and the tip into one unit. That design gives you quick heat-up and tight temperature control. OSS Team lists the T12-BLS with good temperature control and quick thermal conductivity. On a multilayer phone board, the pads pull heat away fast. A tip that recovers quickly lets you finish the joint before neighbouring components absorb the heat. You can also run a lower set temperature for fine work and keep the tip on the pad for less time.

Coating and Tip Life

The manufacturer treats the tip surface and coats the tip end so the tip does not turn black under high temperature. The listing also credits it with good tin-on and tin-melting behaviour, smooth solder flow, and high anti-oxidation with good wetting. You protect that coating with simple habits: tin the tip before you shut the station down, wipe it on brass wool instead of a wet sponge, and avoid leaving the iron at maximum temperature while you work on something else. A tip that stays clean transfers heat better, and better heat transfer means fewer cold joints.

Where It Fits in Your Repair Workflow

You reach for this tip after the heavy removal work finishes. Hot air strips the faulty part, then the soldering iron cleans the pads, tins the contacts, and places jumper wires. Put the board in a PCB holder, work under a microscope, and check continuity with a multimeter before you close the phone. The tip covers charging issue repairs, display connector pad fixes, and small SMD work. When a job calls for lifting a BGA IC, move up to a hot air station and a reballing kit, and keep this tip for the contact-based finishing steps.

Before You Order

Check that your handle takes T12-series tips, because the tip does not fit other iron types. The tip measures approximately 15 cm in length and ships as a single piece. Tips wear out with daily use, so many workshops keep two or three on hand. Browse the Soldering Stations category on Mechanicpk if you need a T12 station to pair with it, and look at other T12 tip shapes when your work needs flat or knife-style contact.

Additional information
Weight0.3 kg
Q & A
Please login to post questions

Key Features

  • Fast thermal conductivity for quick recovery on large pads
  • Good temperature control for fine board work
  • Surface coating resists blackening at working temperature
  • High anti-oxidation with good wetting
  • Smooth tin-on and tin melting behaviour
  • Integrated heater and sensor design of the T12 series
  • Approximate 15 cm tip length
  • Silver and white finish, sold as a single piece

Specifications

BrandOSS Team
ModelT12-BLS
CategorySoldering Iron Tip
CompatibilityT12-series digital soldering stations (listed for 72W digital stations)
TechnologyT12 tip with integrated heating element and temperature sensor
ColorSilver and white
DimensionsLength approx. 15 cm

Common Repair Uses

  • Contact-based soldering on mobile phone boards and general electronics repair.
  • Jumper lagana on broken tracks
  • Charging port pad rework
  • Display and battery connector pad repair
  • Small SMD component replacement
  • Pad cleaning after hot air removal
  • Tinning pads before IC placement
  • Replacing faulty capacitors and resistors on dead phone boards
  • Radio and audio equipment repair

Compatible Devices

  • Universal for T12-series soldering stations. It does not target specific phone models, so it works on any phone board you repair.
  • OSS Team T12 digital soldering stations
  • T12-compatible handles (OSS, Quicko, and Hakko-style T12 stations)
  • 72W T12 digital soldering stations
  • Samsung board repair
  • Oppo and Vivo board repair
  • Infinix and Tecno board repair
  • iPhone board repair
  • Redmi and Realme board repair

FAQ

What is the product name?
The product name is OSS T12-BLS Soldering Iron Tip.
What is the brand of this product?
The brand of this product is OSS Team.
What is the model of this product?
The model of this product is T12-BLS.
What is this product used for?
This product is used for precision soldering on mobile phone boards, including jumper lagana, pad rework, and small component replacement.
Which devices are compatible with this product?
This product is compatible with T12-series digital soldering stations and handles. It works on any phone board you repair, since it is not phone-model specific.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Will the OSS T12-BLS tip fit my soldering station?
It fits stations and handles that take T12-series tips. Check that your handle uses the T12 tip type before you order, because it does not fit other iron types.
How do I stop my T12-BLS tip from turning black?
The tip end carries a coating that resists blackening at high temperature. Tin the tip before you switch off, clean it with brass wool, and avoid leaving the iron at maximum temperature for long periods.