YCS H03 Pro Universal PCB Holder Fixture
₨ 4,200
YCS H03 Pro PCB Holder Fixture
The YCS H03 Pro PCB holder fixture locks mobile phone logic boards in place for hot air rework, reballing, CPU and NAND replacement, and glue removal. Adjustable clamps grip iPhone and Android motherboards, tablet boards and Apple Watch PCBs, and the heat-resistant structure keeps its grip under hot air guns and soldering stations. The circular layout lets you rotate the board under the microscope without re-clamping it. If you handle hardware faults, dead phone jobs and IC change karna work every day, this fixture gives you a steady, repeatable platform at your repair bench.
In stock
YCS H03 Pro PCB Holder Fixture for Chip-Level Mobile Repair
The YCS H03 Pro PCB holder fixture gives your bench a rigid, heat-resistant platform for any logic board that needs hot air, reballing or glue removal. Chip-level work on a dead phone starts with a stable board, and a board that shifts under the nozzle can ruin a CPU or NAND job in seconds. The H03 Pro clamps iPhone, Android, tablet and Apple Watch mainboards in one circular fixture. You rotate the board to reach each chip instead of releasing it and clamping it again.
Clamping Design and Heat Resistance
The H03 Pro holds the board with adjustable clamps, so one fixture covers most smartphone logic boards and many small electronic boards. A dual-clamp system and an adjustable knob let you set the grip to the board’s width without over-tightening. The pressure mechanism holds the board without pressing on the chips, which matters when you work next to a CPU, NAND or PMIC that already sits close to the board edge. The structure resists the heat of hot air guns and soldering stations, and the tempered glass panel gives you a flat, insulated working surface. You can run a long reflow cycle without the clamp softening or the board creeping out of position.
Where It Fits in Your Rework Workflow
Place the H03 Pro between your hot air station and your microscope. Clamp the board, set your preheat, and remove the CPU, NAND or PMIC. Then clean the pads in the same position. The coaxial rotation lets you scrape glue and clean tin without changing the board’s orientation, so you save the minutes you normally lose re-clamping a board between the glue-removal and tin-cleaning passes. The ring-style layout also works with standard microscope setups, so you can inspect pads and solder joints at magnification with the board still locked in place.
After reballing, use the same fixture to reflow the chip, then move to your multimeter for continuity and short checks. Boards with a charging issue, a display problem or a network issue often need a chip pulled and replaced. The H03 Pro keeps that process consistent from the first heat cycle to the last. If you build out your reballing kit, stencil set and soldering station around a fixture like this, every job runs the same way regardless of the phone model.
Choosing the H03 Pro for Your Bench
Basic flat PCB holders work for light jobs, but they force you to reposition the board whenever you switch from desoldering to cleaning. The H03 Pro moves you up that path with a rotating, adjustable platform for both Android and iPhone boards. It suits technicians who handle boot loop issue boards, dead after flash cases that need a hardware check, and hang on logo faults traced to NAND. You also hold the board steady while you jumper lagana on test points or solder ISP wires for eMMC and UFS recovery.
For repair shops in Pakistan that run several technicians on one bench, a universal fixture reduces the need for model-specific holders. One adjustable unit covers mobile phone, tablet and Apple Watch boards, so you spend less on tooling and keep your setup consistent across jobs. Pair it with a hot air station, a soldering station, a microscope and your reballing tools, and it forms the base of a complete chip-level repair setup.
| Weight | 0.4 kg |
|---|
Key Features
- ✓Adjustable clamps fit most smartphone logic boards and small electronic boards
- ✓Dual-clamp system with an adjustable knob for precise grip control
- ✓Heat-resistant structure suits hot air guns and soldering stations
- ✓Tempered glass panel gives a flat, insulated working surface
- ✓Circular layout lets you rotate the board without re-clamping
- ✓Pressure mechanism holds the board without pressing on the chips
- ✓Works with standard microscope setups for magnified inspection
- ✓Universal fit across iPhone, Android, tablet and Apple Watch boards
Specifications
| Brand | YCS |
|---|---|
| Model | H03 Pro |
| Category | PCB Holder / Soldering Fixture |
| Compatibility | Universal – mobile phone, tablet and Apple Watch PCBs |
| Supported Devices | iPhone and Android phone motherboards |
| Technology | Adjustable clamp system with heat-resistant structure |
| Material | Tempered glass panel |
Common Repair Uses
- ✓CPU removal and replacement
- ✓NAND flash chip replacement
- ✓PMIC and other IC change karna jobs
- ✓BGA reballing
- ✓Desoldering with hot air or a soldering station
- ✓Glue removal around chips
- ✓Tin and solder residue cleaning
- ✓Microscope inspection of pads and joints
Compatible Devices
- ✓iPhone motherboards
- ✓Android phone motherboards
- ✓Tablet PCB mainboards
- ✓Apple Watch PCBs
- ✓Small electronic boards
- ✓CPU and BGA chip areas
- ✓NAND flash chip areas
- ✓PMIC chip areas
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can the YCS H03 Pro hold both iPhone and Android boards?
Can the YCS H03 Pro handle hot air during CPU and NAND rework?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



