YCS Silver Flying Line Jumper Wire 0.01mm

₨ 1,300

0.01mm Silver Jumper Wire by YCS

The YCS Silver Flying Line Jumper Wire in 0.01mm diameter gives you a hair-thin conductor for rebuilding broken traces and lifted pads on mobile phone boards. The fine gauge fits between tightly pitched BGA pads and along fingerprint, touch and flex connections, where thicker wire shorts against its neighbours. Silver conducts with low resistance, and YCS builds its flying line range for easy tinning and good toughness. Technicians in Pakistani repair shops use it to fix hardware fault cases such as a dead phone, a charging issue or a display problem caused by one open track. Mechanicpk supplies it for board-level work on Android handsets, iPhones and tablets.

In stock

15 People watching this product now!
Description

0.01mm Silver Jumper Wire for Precision PCB Trace Repair

A 0.01mm silver jumper wire lets you restore broken traces and lifted pads at component level instead of condemning the whole board. The YCS Silver Flying Line Jumper Wire fits where thicker wire cannot: between close BGA pads, along fingerprint and touch flex tracks, and across damaged paths near the CPU. Mechanicpk stocks it for repair shops that handle board-level faults daily and need a consistent, fine-gauge flying line on the bench.

Key Technical Highlights

The 0.01mm diameter defines this wire. At that gauge the conductor sits between neighbouring pads without bridging them, which matters on modern boards where pad pitch keeps shrinking. YCS builds its flying line range around low solder resistance, good toughness and easy tinning, so the wire accepts solder quickly and holds a joint without snapping at the first bend. Silver carries signal with low resistance, which suits data lines and ground returns where a weak joint causes intermittent faults. You tin the end, tack it to the pad, route it across the board surface and finish the second joint under magnification. Pair it with a temperature-controlled soldering station and a fine tip. Low, controlled heat protects both the wire and the surrounding pads.

Repair Workflow Fit

Trace and pad repair sits at the centre of board-level work. A dead phone after a drop, a charging issue from a lifted pad near the charging IC, or a display problem from a torn flex track often comes down to one broken connection. You find the open path with a multimeter, expose clean copper and bridge the gap with a jumper wire. That repair costs far less than a board swap and keeps the customer’s data and original board intact. Technicians also reach for fine flying line after IC change karna, when a pad lifts with the chip and the ball no longer has anything to sit on. A hot air station and a reballing kit handle the chip work, and jumper lagana restores the damaged pad afterwards. Work under a microscope and clamp the board in a PCB holder so your hands stay steady. At 0.01mm the wire gives you no margin for movement.

Bench Handling and Gauge Choice

Cut a short length, tin one end and secure the board before you place the wire. Fine wire tangles easily, so unspool it slowly and keep the spool out of the airflow from your hot air station. Hold the wire with fine tweezers, press it onto the pad and touch the iron briefly. A long dwell time melts the wire end and lifts neighbouring pads. After soldering, route the wire flat against the board and check continuity with your multimeter. Secure the run with UV solder mask or a small drop of glue wherever vibration could stress the joint, and keep the run clear of shielding cans so it cannot short. Store the spool sealed and dry between jobs to slow surface oxidation. Choose 0.01mm for signal, data and fingerprint tracks and for tight-pitch pads. For longer runs or higher-current paths, a thicker gauge such as YCS’s 0.02mm silver wire gives you more current capacity and easier handling.

Additional information
Weight0.9 kg
Q & A
Please login to post questions

Key Features

  • 0.01mm ultra-fine diameter for tight-pitch pad and trace repair
  • Silver conductor for low-resistance signal paths
  • Low solder resistance for fast, clean joints
  • Easy tinning for quick bench setup
  • Good toughness that resists snapping during routing
  • Universal use across Android handsets, iPhones and tablets
  • Suits fingerprint, touch and flex cable track repair
  • Works with standard soldering stations, microscopes and PCB holders

Specifications

BrandYCS
CategoryJumper Wire / Flying Line (Mobile Repair Consumables)
CompatibilityUniversal, not device-specific
MaterialSilver
DimensionsWire diameter 0.01mm

Common Repair Uses

  • Fine trace, pad and flex repair at board level
  • Rebuilding lifted or torn pads after IC change karna
  • Bridging broken PCB traces on dead phone boards
  • Repairing screw-hole tracks that cracked after a drop
  • Restoring damaged CPU-side tracks and BGA pad connections
  • Repairing fingerprint sensor and home button flex tracks
  • Fixing charging issue faults caused by broken tracks near the charging IC
  • Repairing display problem faults from torn flex connector tracks
  • Rerouting damaged signal lines on tablet and laptop boards

Compatible Devices

  • Universal jumper wire for any phone or tablet board that needs trace or pad repair
  • Samsung Android motherboards
  • Oppo and Vivo motherboards
  • Infinix and Tecno motherboards
  • Xiaomi and Redmi motherboards
  • Huawei and Honor motherboards
  • iPhone series logic boards
  • iPad and tablet logic boards
  • Fingerprint, touch and display flex cable tracks

FAQ

What is the product name?
The product name is YCS Silver Flying Line Jumper Wire 0.01mm.
What is the brand of this product?
The brand of this product is YCS.
What is the model of this product?
The product is the YCS Silver Flying Line Jumper Wire in 0.01mm diameter.
What is this product used for?
This product repairs broken PCB traces, lifted pads and damaged flex connections on mobile phone motherboards.
Which devices are compatible with this product?
This jumper wire is universal. You can use it on any phone or tablet board that needs trace or pad repair.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can 0.01mm silver jumper wire repair lifted pads and fingerprint flex tracks?
Yes. The 0.01mm gauge fits between tight-pitch pads and along fingerprint and touch flex tracks. Tin the wire, solder it to the pad and check continuity with a multimeter.
Is a 0.01mm jumper wire suitable for power lines or only signal lines?
A conductor this thin has limited current capacity. Use it for signal, data and ground tracks. For power paths, choose a thicker gauge such as 0.02mm or run several wires in parallel.