YCS-N02 CPU Glue Removal Blade
₨ 300
YCS-N02 Blade for CPU and IC Removal
The YCS-N02 CPU glue removal blade gives board-level technicians a straight, pointed-tip edge for lifting glued CPU and IC chips off mobile phone and tablet motherboards. The deformation-resistant blade holds its shape under pressure, so you keep control while the heated glue releases. Pair it with the curved YCS-N01 when a job needs both chip lifting and black adhesive scraping. Whether you handle IC change karna jobs, dead phone boards, or storage chip removal, the N02 fits into a hot air station, microscope, and PCB holder workflow. Mechanicpk supplies it for Pakistani repair shops and service centers.
In stock
YCS-N02 CPU Glue Removal Blade for Board-Level Rework
The YCS-N02 CPU glue removal blade gives you a straight, pointed-tip edge for one job: separating glued CPU and IC chips from phone and tablet motherboards. YCS splits its chip-rework blades into two profiles. The curved N01 scrapes black adhesive, and the N02 handles the lifting and prying side. When your bench runs IC change karna jobs every day, you need a blade that keeps its geometry once the hot air station softens the epoxy. The N02 uses a deformation-resistant blade, so you control the separation instead of fighting a bent edge.
Blade Profile and Build
The N02 uses a straight blade with a sharp, pointed tip. That tip slips under the edge of a heated chip and breaks the glue bond without wide contact on neighbouring components. A blade that resists deformation matters here, because a flexing edge forces you to press harder, and extra pressure lifts pads and damages traces. With the N02 you apply steady, controlled pressure along the chip edge and let the softened glue release.
YCS positions the blade for CPU removal, IC chip removal, and disassembly of other glued components on mobile and tablet boards. When a job needs both lifting and scraping, pair the N02 with the N01. Use the N02 to free the chip, then switch to the N01 to clear black adhesive around it. Keep the tip clean and replace the blade once the point rounds off, because a dull tip pushes against the chip instead of sliding under it.
Where the N02 Sits in Your CPU Rework Workflow
Start every chip lift with controlled heat. Preheat the board with your hot air station and set the temperature for the board and glue type in front of you. Never pry a cold chip. Secure the board in a PCB holder, bring the area under your microscope, and slide the N02 under one corner of the chip. Work along the edge in small steps and watch the chip release.
After the lift, clean the pads and prepare the chip or the board for the next stage with your reballing kit and soldering station. Check the affected lines with a multimeter before you power up. This sequence turns the N02 into one reliable step inside a larger CPU and IC repair process, not a standalone gadget. You protect the pads, the traces, and the chip in a single pass.
Repair Scenarios Across Pakistani Workshops
Technicians in Pakistani repair markets reach for a blade like the N02 on dead phone jobs, hang on logo cases, boot loop issue boards, and any hardware fault that needs a CPU or storage IC off the board. It also supports chip-off work on storage ICs ahead of eMMC programmer or UFS adapter reading, where you need the chip clear of the board before you read or reprogram it. ISP pinout and test box diagnostics often point to a chip lift as the next step, and the N02 covers that step cleanly.
When you stock your bench, the N02 earns its place beside your hot air station, microscope, and soldering station. It is a small consumable that protects boards worth far more than the blade, and buying a few spares keeps every technician in your shop working with a sharp tip.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Straight blade with a sharp, pointed tip
- ✓Deformation-resistant blade holds its shape under pressure
- ✓Lifts CPU and IC chips from glued motherboards
- ✓Complements the curved YCS-N01 adhesive scraping blade
- ✓Fits microscope-guided precision rework
- ✓Works with hot air station and PCB holder workflows
- ✓Suits mobile phone and tablet board repair
- ✓Supports chip-off preparation for storage ICs
Specifications
| Brand | YCS |
|---|---|
| Model | YCS-N02 |
| Category | CPU Glue Removal Blade / IC Prying Blade |
| Compatibility | Universal, not device-specific |
| Supported Devices | CPU and IC chips on mobile phone and tablet motherboards |
| Technology | Straight pointed-tip, deformation-resistant blade |
Common Repair Uses
- ✓Heat-assisted chip lifting and glue separation during board-level repair
- ✓CPU removal from glued boards
- ✓IC chip lifting during IC change karna jobs
- ✓Breaking glue bonds around chip edges
- ✓Chip-off preparation before eMMC or UFS reading
- ✓Dead phone board rework
- ✓Hang on logo and boot loop hardware fault repair
- ✓Pad area preparation before cleaning and reballing
- ✓Component removal during board disassembly
Compatible Devices
- ✓Universal blade, not tied to specific phone models; it works on glued CPU and IC chips on mobile and tablet boards
- ✓Mobile phone motherboards
- ✓Tablet motherboards
- ✓Glued CPU chips
- ✓Glued IC chips
- ✓BGA chips on repair boards
- ✓Storage ICs prepared for chip-off work
- ✓Other glued board components
- ✓Boards that need heat-assisted chip lifting
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can I use the YCS-N02 blade on a cold board?
What is the difference between the YCS-N01 and YCS-N02 blades?
Related products
RELIFE RL-004SA silicone pad – Anti-slip
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



