2UUL PB02 PadBall Solder Balls for Android Pad Rework

₨ 1,900

PadBall Solder Balls for Android Pad Rework

The 2UUL PB02 PadBall Solder Balls give you 100,000 pre-formed Sn63/Pb37 balls in one bottle, made for rebuilding missing solder joints on Android motherboard pads. The eutectic alloy melts at 183°C, so each ball reflows cleanly under a hot air station or soldering iron and bonds to the pad without extra material. PB02 targets Android boards, while the sister PB01 covers iPhone work. Mechanicpk stocks this bottle for Pakistani repair shops that handle lifted pads, torn BGA joints, and charging issue boards every day and want a consistent, ready-to-place solder ball supply on the bench.

Out of stock

15 People watching this product now!
Description

Solder Balls for Android Pad Rework Built for Bench-Level Repair

The 2UUL PB02 PadBall Solder Balls are solder balls for Android pad rework, supplied as 100,000 pre-formed Sn63/Pb37 spheres in a single bottle. You restore missing solder joints on a motherboard pad without dragging wire, guessing paste volume, or rebuilding the joint by hand. Mechanicpk stocks PB02 as a spec-driven consumable with a known alloy, a known quantity, and a known melting point, so you plan your bench stock with confidence. You place a ball on the bare pad, apply heat, and the pad regains the joint your IC needs to sit flat. That repeatable result matters when a dead phone arrives with a lifted pad and your margin depends on a clean first attempt.

Sn63/Pb37 Eutectic Alloy and Reflow Behavior

Sn63/Pb37 is a eutectic alloy, which means it melts at one fixed point, 183°C, instead of passing through a pasty range. The ball flips from solid to liquid in one step, wets the copper pad quickly, and freezes without the dragging stage that shifts a part during reflow. Distributor listings describe the PB02 balls as low in oxidation with minimal residue, which helps you keep bridging risk down on tight BGA and CSP pads. Note that the alloy contains lead. Keep your pad cleaning, flux choice, and reflow temperature matched to a leaded workflow, and avoid mixing it with lead-free solder on the same joint, because mixed alloys change how a joint melts and solidifies.

How PB02 Fits an Android Repair Workflow

Start with diagnosis. Check the rails with a multimeter, inspect the suspect area under a microscope, and clamp the board in a PCB holder so it stays flat. Lift the IC with a hot air station, clean the leftover solder with a soldering station, and look for pads that tore away with the chip. That is where PB02 earns its place: you set a ball on each damaged pad, reflow it, and rebuild the joint at its original position. After the pad rework, you move to reballing kits and stencils for the IC itself, reseat the chip, and confirm the repair. When the fault involves storage, you bring in ISP pinout tools, eMMC programmers, or UFS adapters to read or reflash the chip, and test boxes handle the final function checks. Every one of those categories sits one step away from this bottle in the same repair chain.

Prep decides the result. Clean the pad down to bright copper, apply a thin layer of flux, and keep the board supported so the ball cannot roll. Place one ball per damaged pad with fine tweezers, then bring your hot air station to a controlled temperature above 183°C so the ball melts and wets the pad. Watch it under the microscope until it collapses into a smooth dome, and let the board cool before you touch it. Inspect each rebuilt pad for height and position before the IC goes back on.

Why Technicians Choose Solder Balls for Android Pad Rework

Hand-fed solder leaves uneven joint height, and uneven height lifts an IC corner and kills a connection. Uniform PadBall solder balls for Android pad rework give you consistent solder volume pad after pad, which speeds up boards that arrive with a charging issue or a hardware fault traced to a lifted pad, especially when you restore several pads in one session. At 100,000 balls per bottle, one purchase covers a long run of repairs and keeps the consumable cost per job low for busy shops and service centers. Match the variant to the platform: PB02 targets Android boards, while 2UUL sells the PB01 bottle for iPhone pad rework, so you avoid ordering the wrong one. Pakistani repair shops that run IC removal and board repair every day burn through consumables fast, and a 100,000-ball bottle keeps your stock steady between orders. The bottle measures 16 x 16 x 32 mm, so it fits a bench drawer or tool tray without crowding your flux and solder paste.

Additional information
Weight0.9 kg
Q & A
Please login to post questions

Key Features

  • Sn63/Pb37 eutectic alloy for smooth reflow and strong joints
  • Single 183°C melting point for predictable wetting
  • 100,000 balls per bottle for long repair runs
  • Uniform ball size for consistent solder volume per pad
  • High-conductivity solder for reliable electrical joints
  • Low-oxidation formulation with minimal residue
  • PB02 variant dedicated to Android solder pad rework
  • Compact 16 x 16 x 32 mm bottle that fits any bench

Specifications

Brand2UUL
ModelPB02
CategorySolder Balls (BGA / Solder Pad Rework Consumable)
CompatibilityAndroid phone motherboards
Supported DevicesAndroid phones
TechnologySn63/Pb37 eutectic solder alloy, 183°C melting point
MaterialSn63/Pb37 solder alloy
Quantity100,000 pcs per bottle
Dimensions16 mm x 16 mm x 32 mm (bottle)

Common Repair Uses

  • Restoring missing solder joints on Android motherboard pads
  • BGA and CSP pad restoration
  • Micro-soldering work on small pads
  • Rebuilding pads that tore away during IC removal
  • Pad rework before reseating an IC on a dead phone board
  • Pad repair on boards with a charging issue or hardware fault traced to a lifted pad

Compatible Devices

  • Android phone motherboards. The listing is platform-level and brand-agnostic, so no individual phone models apply.
  • Android smartphone motherboards with missing solder joints
  • Android boards with lifted or torn BGA pads
  • Android boards with damaged CSP pads
  • Any Android PCB that needs micro-soldering pad restoration

FAQ

What is the product name?
The product name is 2UUL PB02 PadBall Solder Balls.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is PB02.
What is this product used for?
This product is used for rebuilding missing solder joints on Android phone motherboard pads during solder pad rework.
Which devices are compatible with this product?
This product is compatible with Android phone motherboards.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Is the 2UUL PB02 solder ball lead-free, and what is its melting point?
No. PB02 uses a Sn63/Pb37 alloy, which contains lead and melts at 183°C. Use it with a leaded workflow and avoid mixing it with lead-free solder on the same joint.
What is the difference between 2UUL PB01 and PB02 PadBall solder balls?
PB01 is made for iPhone solder pad rework and PB02 is made for Android solder pad rework. Both come as 100,000 balls per bottle.