YCS 138°C 50g BGA Solder Reballing Paste

₨ 1,200

138°C Low-Temp BGA Reballing Paste

The YCS 138°C BGA solder paste comes in a 50g container for technicians who reball and rework mobile phone boards daily. Its 138°C melting point keeps reflow heat low around heat-sensitive ICs, flex connectors and multilayer logic boards. YCS positions it for BGA, IC, CPU and PCB precision soldering repair. Pair it with a hot air station, a reballing stencil kit and a PCB holder to build a complete chip-level workflow. Mechanicpk supplies it to Pakistani repair shops and service centers that need a predictable low-temperature paste on the bench.

In stock

15 People watching this product now!
Description

138°C BGA Solder Paste for Low-Heat Mobile Board Reballing

The YCS 138°C BGA solder paste gives your bench a low-melting option for reballing and chip-level rework on mobile phone motherboards. A 138°C melting point sits well below the working range of medium and high temperature pastes, so the board, the neighbouring ICs and the flex connectors take less heat while you work. YCS packs this paste in a 50g container, which suits shops that reball boards daily and burn through paste fast. Mechanicpk supplies it to Pakistani repair shops and service centers that want predictable reflow on heat-sensitive boards.

Why a 138°C Melting Point Matters on a Logic Board

Every reballing job runs on a heat budget. A multilayer logic board carries a CPU, memory, power ICs and flex connectors within a few millimetres of each other, and every extra degree you push into that board raises the risk of lifted pads, a warped PCB or a dead phone after the repair. A paste that melts at 138°C lets you reflow at a lower hot air setting than a 183°C paste demands. Pair it with a hot air station that holds steady airflow and you control the heat instead of chasing it. YCS also lists 150°C and 183°C pastes, so you can step up to a higher melting point when a board or component calls for it. Set your station around the paste’s 138°C melting point, then run a short test reflow on a scrap board or spare chip before you touch a customer’s phone. Preheat the board from below if your station supports it, since even heating narrows the temperature gap between the chip and the PCB.

Where It Fits in Your Repair Workflow

YCS positions this paste for BGA, IC, CPU and PCB precision soldering repair, and that covers most chip-level jobs on a mobile repair bench. After you lift a chip, clear the old solder off the pads with your soldering station and wick, then fix the board in a PCB holder so it stays flat under the stencil. Press the stencil from your reballing kit onto the chip, spread the paste through the apertures and reflow it with hot air until the balls form. Check every ball under a microscope for bridges and uneven sizes before you place the chip back on the board. Measure the pads with a multimeter for shorts before you power up. For eMMC or UFS work, confirm the fix with your ISP pinout tool, eMMC programmer or UFS adapter, then run a final check on a test box.

Repairs It Handles and What to Know Before You Buy

IC change karna on a board with a charging issue, hang on logo after a memory fault, a hardware fault that shows up as a dead phone once you trace it to a BGA chip: each of these jobs ends with a reflow, and a low-melting paste keeps that reflow gentler on the surrounding parts. Pad repair, flex cable area soldering and rework near heat-sensitive ICs follow the same logic. You keep the thermal load down and your reflow profile simple. When a CPU or memory chip needs a fresh set of balls, you apply the paste through the stencil in a thin, even layer and reflow once, which keeps the chip’s time under heat short.

The YCS 138 model ships in a 50g pack with a 138°C melting point. That gives a busy workshop a lot of material per container and a single temperature to dial into your hot air profile. Follow the storage guidance on the container label, and close the container after each use so the paste stays workable. Shops that stock one paste per temperature range keep jobs organised and avoid mixing profiles at the bench. If your bench also needs a higher heat range for other jobs, browse the Hot Air Stations, Soldering Stations and Reballing Kits categories on Mechanicpk and build the full reballing setup in one order. This 138°C BGA solder paste slots into that setup as your low-heat option.

Additional information
Weight0.50 kg
Q & A
Please login to post questions

Key Features

  • 138°C low melting point for reduced thermal load
  • 50g container for daily workshop use
  • Positioned by YCS for BGA, IC, CPU and PCB precision soldering
  • Suits heat-sensitive ICs and flex cable areas
  • Works on multilayer mobile logic boards
  • Fits a hot air station and stencil reballing workflow
  • Part of a YCS range with 150°C and 183°C options
  • Brand-independent, universal use on mobile boards

Specifications

BrandYCS
ModelYCS 138
CategorySolder Paste / BGA Reballing Consumables
CompatibilityUniversal, not device-specific
TechnologyLow-temperature solder paste, 138°C melting point
Weight50g net content

Common Repair Uses

  • BGA, IC, CPU and PCB precision soldering on mobile boards.
  • BGA reballing with a stencil
  • IC installation after IC change karna
  • CPU reflow and reballing
  • Pad repair
  • Heat-sensitive component rework
  • Flex cable area soldering
  • Charging IC rework on boards with a charging issue
  • Reballing on hardware fault boards (dead phone, hang on logo) after fault tracing

Compatible Devices

  • Universal, not device-specific. Suits mobile phone logic boards and BGA, IC and CPU rework regardless of brand.
  • Mobile phone motherboards (brand-independent)
  • BGA packages on phone logic boards
  • CPU rework and reballing
  • Memory and power IC rework
  • Multilayer logic boards
  • Heat-sensitive ICs
  • Flex cable and connector areas
  • General PCB precision soldering

FAQ

What is the product name?
The product name is YCS 138°C 50g BGA Solder Reballing Paste.
What is the brand of this product?
The brand of this product is YCS.
What is the model of this product?
The model of this product is YCS 138.
What is this product used for?
This product is used for BGA reballing, IC and CPU rework and PCB precision soldering on mobile phone boards.
Which devices are compatible with this product?
This product is universal and not device-specific. It suits mobile phone logic boards and BGA, IC and CPU rework regardless of brand.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What is the melting point of YCS 138 solder paste?
The melting point is 138°C, which is lower than YCS’s 183°C medium-temperature paste, so reflow puts less heat into the board.
Does YCS offer this paste in other temperature grades?
Yes. YCS also lists 150°C and 183°C low and medium temperature pastes in 50g containers, so you can pick the melting point that fits the board.