2UUL BA15 Back Cover Sealing Adhesive for iP15 (5pcs/Pack)
₨ 900
Pre-Cut Sealing Adhesive for iPhone 15 Back Glass
The 2UUL BA15 Back Cover Sealing Adhesive for iP15 (5pcs/Pack) gives you five pre-cut, double-sided gaskets shaped to the iPhone 15 rear frame. Each piece follows the frame outline, so you reseal the back glass without trimming or guesswork. You apply heat during installation to rebuild the seal and restore airtightness after a repair. This iPhone 15 back cover sealing adhesive suits Pakistani repair shops that reopen the rear panel for battery, charging port, board-level, or glass replacement jobs and need one consistent closing step at the bench.
In stock
iPhone 15 Back Cover Sealing Adhesive Built for Repeatable Rear Panel Reseals
The 2UUL BA15 Back Cover Sealing Adhesive for iP15 (5pcs/Pack) is a model-specific consumable for technicians who open the iPhone 15 from the rear. The phone opens through the back glass, so every battery, charging port, or board-level job breaks the factory perimeter seal the moment you separate the glass. This iPhone 15 back cover sealing adhesive replaces that seal with a pre-cut, double-sided gasket you place on the frame before you close the phone. Each pack holds five pieces, which covers five reseals at your bench before you reorder.
Pre-Cut Geometry and Heat-Assisted Bonding
The BA15 uses an outline matched to the iPhone 15 rear frame, so the adhesive sits exactly where the original seal ran. You peel, align, and press, with no cutting, trimming, or stretching. The recommended installation method is thermal sealing: you warm the adhesive during installation so it bonds the frame and glass and restores airtightness. Heat control decides the result. A hot air station on low airflow or a heat plate gives you even warmth around the perimeter, and a PCB holder keeps the frame steady while you press the glass down. Final water resistance depends on clean surfaces, correct alignment, and applied pressure, so treat the adhesive as one part of a proper reseal and not a guarantee on its own.
Where It Sits in the iPhone 15 Repair Workflow
An iPhone 15 that reaches your bench with a charging issue, a dead phone after a drop, or a cracked back glass ends with the same closing sequence. You open the rear panel, lift the leftover adhesive from the frame with blunt tweezers, and wipe the glass perimeter with 90%+ isopropyl alcohol if you reuse the glass. You finish the hardware fault repair and run a power test before you seal. That test step saves you the most adhesive: reconnect the battery, boot the phone, confirm the fix, power down, and only then apply the BA15. You never burn a gasket on a phone that still needs board work. Use your multimeter during diagnosis and your microscope for connector inspection, then seal once everything passes. In a busy Pakistani repair shop, a five-piece pack matches the weekly pace of glass replacements, battery changes, and charging port jobs on the same model.
Model Matching: BA15 Fits the Standard iPhone 15
The BA15 targets the standard iPhone 15. 2UUL sells separate codes for other 15-series variants, such as BA15PS for the iPhone 15 Plus and BA15P for the iPhone 15 Pro, because each model has its own frame outline. Confirm the model under Settings > General > About before you open the pack. Mixing sizes wastes pieces and leaves gaps in the seal. Budget one piece per reseal and keep the spares for a second attempt if the glass shifts during alignment. This adhesive belongs with the other rear-panel service consumables in the Mechanicpk range, alongside hot air stations, PCB holders, microscopes, and multimeters, so you can build a complete iPhone back glass service setup from one supplier.
| Weight | 0.100 kg |
|---|
Key Features
- ✓Pre-cut outline made for the iPhone 15 rear frame
- ✓Double-sided adhesive gasket for back cover installation
- ✓Heat-assisted (thermal) sealing to restore airtightness after repair
- ✓Five pieces per pack for multiple reseals
- ✓Model-specific BA15 code that prevents size mix-ups with 15 Plus and 15 Pro adhesives
- ✓Aligns directly to the frame, with no cutting or trimming
- ✓Suits back glass replacement and post-repair reassembly
- ✓Gives technicians a repeatable closing step across daily iPhone jobs
Specifications
| Brand Entity | 2UUL |
|---|---|
| Product Entity | 2UUL BA15 Back Cover Sealing Adhesive (5pcs/Pack) |
| Technology Entity | Pre-cut double-sided sealing adhesive, thermal (heat-assisted) sealing |
| Compatible Device Entities | Apple iPhone 15 |
| Repair Process Entity | iPhone 15 back glass resealing, rear panel reassembly |
| Industry Entity | Mobile phone repair consumables, iPhone repair in Pakistan |
Common Repair Uses
- ✓Back glass replacement on a cracked iPhone 15
- ✓Resealing the rear panel after battery replacement
- ✓Resealing after charging port repair
- ✓Closing the phone after board-level repair on a dead phone
- ✓Reassembly after connector or flex cable inspection
- ✓Re-sealing a reused back glass after cleaning the perimeter
Compatible Devices
- ✓Model-specific to the Apple iPhone 15
- ✓Apple iPhone 15 (standard model)
- ✓iPhone 15 Plus, 15 Pro, and 15 Pro Max need their own model-specific adhesive and are not covered by the BA15
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the 2UUL BA15 fit the iPhone 15 Plus, 15 Pro, or 15 Pro Max?
Does the 2UUL BA15 need heat to seal the back cover?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



