2UUL PW15 Power Host Ampere-Voltage Meter

₨ 5,500

Live Voltage and Current Readout for Phone Boot Testing

The 2UUL PW15 power host connects your DC power supply to the phone boot cable and shows the voltage and current a motherboard draws while it boots. A one-button power-on, a 5.2V over-voltage cut-off with alert, and a 4mm banana plug interface keep the bench setup quick and safe. The pack includes the meter, a Type-C 5V power cord, and a USB-A 5V power cord. Technicians use it on dead phone and short-circuit cases to see where the board stops pulling current, before they pick up a hot air station or soldering iron.

In stock

10 People watching this product now!
Description

2UUL PW15 Power Host: Boot Current Monitoring for Board-Level Repair

The 2UUL PW15 power host gives you a direct read on what a logic board draws the moment you power it. It links your DC power supply to the phone boot cable and shows voltage and current on a built-in digital display, so you judge a dead phone by numbers instead of guesses. Mechanicpk lists it under Multimeters, alongside the other diagnostic instruments a Pakistani repair bench needs before any IC change. The PW15 keeps its job narrow: it supplies, monitors, and protects during the boot test, and your measurements drive the repair decision.

Reading Current as an Ampere-Voltage Meter for Mobile Repair

Every board-level fault starts with the same question: does the board draw current, and how much? Connect the boot cable, long-press the button for one-touch power-on, and watch the display. A board that draws nothing points you toward a missing supply rail or an open power path. A board that pulls high current the instant it powers up points you toward a short. Both readings tell you where to probe next, and they cost you no component.

The same display helps with the faults that waste the most bench time. On a boot loop issue, you see the current climb and drop in a repeating pattern. On a hang on logo case, you see the current settle at a fixed level. On a dead after flash phone, you compare the reading against a known-good board and decide whether the fault sits in software or hardware.

Protection Limits You Need to Know

The PW15 cuts power and sounds an alert when voltage passes 5.2V, which protects the board from a wrong setting or a supply spike during testing. The operating voltage stays at DC 8.2V and below, so you keep your bench supply under that ceiling and never exceed it. The 4mm banana plug connector matches most power cords and boot cables used in phone repair, and the Type-C 5V and USB-A 5V cords in the pack cover the common 5V input options.

Where It Sits Next to Your Other Tools

The PW15 handles the first check, and the rest of your bench handles the fix. Pair it with Multimeters for rail-by-rail measurement and Microscopes to inspect the board once the current reading narrows the fault. Hold the board in PCB Holders while you probe, then move to Hot Air Stations, Soldering Stations, and Reballing Kits for the rework itself. On storage-related cases, confirm the board draws normal current before you spend time on ISP Pinout Tools, eMMC Programmers, UFS Adapters, or Test Boxes. If your work later demands a wider voltage range or multi-channel measurement, step up to a bench-class tester and keep the PW15 as your quick-boot station.

Additional information
Weight0.25 kg
Q & A
Please login to post questions

Key Features

  • Built-in digital display for real-time voltage and current
  • Automatic power-off with alert above 5.2V
  • One-button power-on for quick boot tests
  • 4mm banana plug interface for wide cord compatibility
  • Operating voltage of DC 8.2V and below
  • Type-C 5V power cord included
  • USB-A 5V power cord included
  • Compact, lightweight body for bench or field repair

Specifications

Brand2UUL
ModelPW15
CategoryMultimeters
CompatibilityPower cords and phone boot cables with 4mm banana plug
Supported DevicesAndroid and iPhone logic boards, through a matching boot cable
TechnologyDigital voltage and current display with one-button power-on and 5.2V over-voltage auto power-off
Input VoltageDC 8.2V and below (do not exceed 8.2V)

Common Repair Uses

  • Power-up diagnostics on mobile motherboards, from the first boot test to the final check after rework
  • Boot testing a dead phone without a battery
  • Spotting short circuits from abnormal current draw
  • Watching the current pattern on a boot loop issue
  • Checking current level on a hang on logo fault
  • Comparing a dead after flash board against a known-good board
  • Verifying a board before and after an IC change
  • Monitoring voltage during one-touch power-on testing
  • Protecting the board from over-voltage during bench tests

Compatible Devices

  • Universal — not device-specific; works with any board that has a matching boot cable ending in a 4mm banana plug
  • Android phone logic boards through a matching boot cable
  • iPhone logic boards through a matching boot cable
  • Samsung, Oppo, Vivo, Infinix, and Tecno boards with an available boot cable
  • DC power supplies with 4mm banana output
  • 5V USB-A power sources (cord included)
  • 5V Type-C power sources (cord included)
  • Boot cables and power cords with 4mm banana plug
  • Battery-free boot setups on the repair bench

FAQ

What is the product name?
The product name is 2UUL PW15 Power Host Ampere-Voltage Meter.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is PW15.
What is this product used for?
This product is used for powering a phone motherboard through a boot cable while showing the voltage and current the board draws.
Which devices are compatible with this product?
This product is compatible with Android and iPhone logic boards through a matching boot cable that ends in a 4mm banana plug.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What happens if the voltage goes above 5.2V on the 2UUL PW15?
The PW15 cuts the power automatically and sounds an alert, which protects the board from over-voltage.
What is the maximum operating voltage for the 2UUL PW15?
The operating voltage must stay at DC 8.2V or below. Do not connect a supply above 8.2V.