Sunshine SS-024 Precision Multimeter Pen
₨ 900
Precision Probing for Phone Boards
The Sunshine SS-024 Precision Multimeter Pen gives your multimeter a 2 mm super-pointed tip for pad-level testing on phone motherboards. This precision multimeter pen for mobile repair carries a CAT III, 1000 V / 20 A rating, a 970 mm PVC lead and a non-slip PVC handle, and it fits multimeters with φ4 mm sealed banana jacks. You use it for continuity checks, diode-mode short hunting and voltage checks on dead phone and charging issue boards. Mechanicpk supplies the SS-024 to repair shops and service centers across Pakistan.
In stock
Sunshine SS-024 Precision Multimeter Pen for Board-Level Probing
The Sunshine SS-024 Precision Multimeter Pen swaps your meter’s thick factory probes for a 2 mm super-pointed tip that lands on one test pad instead of three. If you want a precision multimeter pen for mobile repair, this lead set gives you CAT III, 1000 V / 20 A rated probing with a 970 mm cable that keeps the meter clear of your hot air station and soldering area. It plugs into multimeters with φ4 mm sealed banana jacks, so the meter already on your bench works with it from day one. Pakistani repair shops that handle daily dead phone and charging issue jobs use a pen like this to turn slow, guess-and-check probing into fast, readable measurements.
Needle Tip, Lead and Handle Build
The SS-024 uses a needle-style probe with a 2 mm diameter that reaches a pad sitting behind a tall capacitor or beside a shield frame. The gold-plated tip resists oxidation, so your contact stays clean across a full shift of continuity checks. A non-slip PVC handle gives you a steady grip when you hold the pen at a shallow angle over a dense board, and a dust plug covers the connector end between jobs.
Fine tips matter on modern boards. Phone PCBs pack pads at fine pitch, and a wide probe shorts two lines at once and sends you chasing a fault that does not exist. A sharp 2 mm needle keeps each reading tied to one pad, so the numbers you write down describe the actual line you touched.
The pen measures 1100 mm overall with a 970 mm PVC lead. That length lets you park the meter on the far side of your bench and keep the working area around the board open for tweezers, flux and a microscope arm. The SS-024 is a test lead set, not a standalone meter. It needs a multimeter to display your readings.
Where It Fits in a Mobile Repair Workflow
A dead phone or a charging issue usually starts with a short on a power rail, and a thick probe makes that hunt slow and risky. With the SS-024, you set your multimeter to diode or continuity mode, touch the 2 mm tip to a pad, and read the line without bridging the neighbouring pads. You repeat the same move down the rail until the reading tells you which component pulls the line low.
The pen belongs in the diagnostics stage of the PCB repair process, before you commit to hot air station or soldering station rework. You use it to trace a broken track before jumper lagana, to confirm a capacitor or resistor before replacement, and to verify a line after an IC change karna. Most technicians run it under a microscope with a PCB holder gripping the board, so both hands stay steady while the tip sits on the pad.
After rework, you pick the pen up again to confirm the repair. That final continuity and voltage check closes the testing loop on a hardware fault job and tells you whether to power the board on or reopen the rework.
What to Confirm Before You Order
Check your meter’s jacks first. The SS-024 fits φ4 mm sealed banana sockets, which covers standard digital multimeters. The 1000 V / 20 A rating describes the pen, and your meter’s own input rating still sets your working limit, so read the label on the meter before you probe a high-current line.
Technicians who build a complete diagnostic bench usually pair this pen with a reliable multimeter, a test box for power-on checks, and a microscope for pad-level work. Mechanicpk stocks each of those categories, so you can upgrade from a basic probe setup to a full board-level bench in steps.
| Weight | 0.15 kg |
|---|
Key Features
- ✓2 mm super-pointed needle tip for single-pad contact
- ✓CAT III safety rating at 1000 V / 20 A
- ✓Gold-plated tip that resists oxidation
- ✓Non-slip PVC handle for steady control
- ✓970 mm PVC lead for flexible bench layout
- ✓1100 mm overall length
- ✓Dust plug protects the connector end
- ✓Plugs into φ4 mm sealed banana jacks
Specifications
| Brand | Sunshine |
|---|---|
| Model | SS-024 |
| Category | Multimeter Test Lead Pen / Mobile Repair Probe |
| Compatibility | Multimeters with φ4 mm sealed banana jacks |
| Technology | Super-pointed needle tip, CAT III, 1000 V / 20 A rated |
| Material | PVC handle and lead wire, gold-plated needle tip |
| Dimensions | Total length 1100 mm, lead length 970 mm, probe diameter 2 mm |
Common Repair Uses
- ✓Pad-level testing during mobile phone motherboard diagnostics
- ✓Continuity testing on broken PCB tracks
- ✓Diode-mode short hunting on dead phone boards
- ✓Voltage checks on charging issue boards
- ✓Verifying capacitor and resistor terminals before replacement
- ✓Checking a line before jumper lagana
- ✓Post-repair verification after IC change karna
- ✓Probing fine-pitch pads under a microscope
- ✓Final testing after hot air or soldering rework
Compatible Devices
- ✓Universal multimeter test lead — not device-specific
- ✓Digital multimeters with φ4 mm sealed banana jacks
- ✓Analog multimeters with standard banana inputs
- ✓Benchtop multimeters with standard banana sockets
- ✓Multimeter series that accept standard plug-in test leads
- ✓Android smartphone motherboards (probing only, universal)
- ✓iPhone logic boards (probing only, universal)
- ✓Charging, power and audio line test points on any phone PCB
- ✓Fine-pitch SMD pads and component terminals
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is the Sunshine SS-024 a standalone multimeter?
Which multimeter jacks does the SS-024 fit, and what is its rating?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock



