SUNSHINE P-3010D Adjustable DC Power Supply 30V 10A
₨ 21,000
30V 10A Bench Power Supply
The SUNSHINE P-3010D Adjustable DC Power Supply gives your repair bench an adjustable 0-30V output with a 10A current ceiling, so you can power phone boards and tablets without a battery. A high-stability transformer drives the unit, copper core connection posts carry the load, and the 220V input plugs straight into workshop mains. You use this 30V 10A DC power supply for mobile repair to read current draw on a dead phone, trace short circuits and confirm a board powers up after an IC change. The pack includes a power cable and additional cables, so you can start testing on day one.
30V 10A DC Power Supply for Mobile Repair: SUNSHINE P-3010D Overview
Every board that reaches your bench starts the same way: you connect power, watch the current, and decide where to probe next. The SUNSHINE P-3010D Adjustable DC Power Supply turns that first step into a measured test. As a 30V 10A DC power supply for mobile repair, it gives you an adjustable 0-30V output, a 10A maximum current and a digital readout of voltage and current, so a dead phone tells you where the fault sits before you lift a single IC. Mechanicpk stocks it for technicians and shop owners across Pakistan who want dependable bench power without a complicated interface.
Sunshine builds the P-3010D around a high-stability transformer and copper core connection posts. Distributor listings give a 220V input and a 0-30V adjustable output with a 10A maximum, in a body that measures 170 x 210 x 330 mm and weighs 5.8 kg net. That output window covers the battery-voltage rails of phone and tablet boards with plenty of headroom, and the current ceiling leaves room for loads far above what a phone board draws.
Technical Highlights at a Glance
You set the output voltage anywhere from 0V to 30V, and the current output tops out at 10A. Phone boards run on a narrow battery-voltage range, so the lower end of the dial does most of the daily work, while the upper range serves larger loads when a job calls for it. The high-stability transformer carries the load, and at 5.8 kg net the unit sits firmly on the bench when you pull leads across the table.
Copper core connection posts take your test leads. The pack includes a power cable and additional cables, so you can start testing as soon as you unbox the unit. The 220V input matches standard workshop mains, which means you plug in and work without a step-down adapter.
Where It Fits in the Repair Workflow
A bench power supply sits at the very start of the diagnostics process, before the hot air station, before the soldering iron and before any flashing. You connect the board without its battery, set the voltage to the battery rating, and read the current on the display. A dead phone that draws nothing points you toward the power path or the battery connector. A board that pulls high current the moment you power it points you toward a short on a rail, and your multimeter and microscope take it from there.
After an IC change or a reflow, the supply doubles as your first power-up test. You bring the board up at the battery voltage, watch the current settle, and confirm the repair before you reassemble the phone. That one step saves you from a full rebuild and a returned device.
The same readout helps with a boot loop issue or a hang on logo fault. Watch how the current behaves while the phone tries to start: a board that never draws current needs a different approach than one that draws current and then drops back, and each pattern narrows your next probe point. After a dead-after-flash case, the reading shows you quickly whether the board still wakes up or needs hardware attention. Charging issue jobs also benefit, because you can power the board directly and separate a bad charging IC or port from a failing battery.
Protection and Bench Safety
Distributor listings describe the P-3010D with a cooling fan and automatic protection against overload and high temperature. Those features matter on a busy repair bench, where one unit runs for hours while you swap boards. Good habits still protect your board better than any built-in feature. Set the voltage first, then connect the leads, and keep the output within the battery rating of the phone you test. Treat the 10A ceiling as a limit for the supply, not a target for the board.
Choosing the P-3010D for Your Shop
Shop owners with several technicians usually keep one supply per bench, and the P-3010D suits that setup because it keeps controls simple and readings clear. Pair it with a good multimeter for rail checks, a microscope for inspecting the board, and a hot air station and soldering station for the repair itself. PCB holders keep the board steady while you probe under power. If your work moves into flashing, test boxes, ISP pinout tools, eMMC programmers and UFS adapters build on the same dead-phone diagnosis you start with this supply, and reballing kits cover the jobs where a scan points to a failed chip. The result is a repeatable routine your whole team follows: same voltage setting, same lead connections, same current check on every dead phone.
Choose the SUNSHINE P-3010D when you want a spec-driven, no-nonsense 30V 10A bench supply that handles daily phone diagnosis and still has capacity for larger loads.
| Weight | 5.8 kg |
|---|
Key Features
- ✓Adjustable output from 0V to 30V
- ✓Maximum output current of 10A
- ✓High-stability transformer
- ✓Copper core connection posts
- ✓Digital readout of voltage and current
- ✓Cooling fan for sustained bench use
- ✓Automatic overload and high-temperature protection
- ✓220V input with power cable and additional cables in the pack
Specifications
| Brand | SUNSHINE |
|---|---|
| Model | P-3010D |
| Category | DC Power Supply |
| Compatibility | Universal, not device-specific |
| Supported Devices | Any low-voltage DC load within 0-30V and 10A |
| Technology | High-stability transformer |
| Input Voltage | 220V |
| Output Voltage | 0-30V, adjustable |
| Dimensions | 170 x 210 x 330 mm |
| Weight | 5.8 kg (net) |
Common Repair Uses
- ✓Current-draw diagnosis and power-up testing at the repair bench
- ✓Dead phone diagnosis by reading current at power-up
- ✓Short-circuit tracing on power rails
- ✓Boot loop and hang on logo current monitoring
- ✓Charging issue testing with direct board power
- ✓Power-up check after IC change or reflow
- ✓Dead-after-flash hardware check
- ✓Battery-free board testing
- ✓Bench testing of low-voltage DC components
Compatible Devices
- ✓Universal bench power source, not device-specific; it powers any board that runs within 0-30V and 10A
- ✓Android smartphone motherboards (Samsung, Oppo, Vivo, Infinix, Tecno, Xiaomi)
- ✓iPhone logic boards
- ✓Tablet motherboards
- ✓Dead phone boards tested without a battery
- ✓Boards after IC replacement or reflow
- ✓Boards with a suspected short on a power rail
- ✓Low-voltage DC accessories and modules
- ✓Components and circuits under bench testing
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What output voltage and current range does the SUNSHINE P-3010D offer?
Does the P-3010D have overload and over-temperature protection?
Related products
818F Smart Wireless Fast Charger 6-in-1 with LCD Display
In stock
Aifen 3310 Pro 33V/10A 330W Adjustable DC Power Supply
In stock
Mechanic V90E Digital Multimeter – Voice Broadcast Meter
In stock
Relife RL-727 3D Extreme Pentalobe 0.8 Screwdriver
Out of stock


